Diagnosis and resolution of high discharge temperature of a screw compressor

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Diagnosis and resolution of high discharge temperature of a screw compressor

1. Problem Description and Area of Application

High discharge temperature of a screw compressor (usually exceeding the threshold of the emergency alarm +105 °C and causing an emergency shutdown of the compressor at the setting +110 °C) is a critical failure that directly affects the reliability of the equipment. This manual covers oil-filled screw compressors with capacities from 1 to 50 m³/min, which are operated on industrial enterprises in Ukraine under conditions of variable loading and increased dustiness.

Classification of severe consequences:

  • Critical (Class A): Excess intake temperature above +110 °C. Causes immediate emergency stop. Risk of oil coking, screw blockage, destruction of polymer seals.
  • Significant (Class B): The discharge temperature is maintained within the range of +100...+105 °C during operation with full load. The oil life is reduced by two or more times, and the load on the separation system increases.
  • Moderate (Class C): A slow temperature rise of 5–10 °C is observed compared to the base seasonal indicators under the same load.

2. Precautionary Measures and Safety

ПОПЕРЕДЖЕННЯ БЕЗПЕКИ (LOTO): Перед початком будь-яких діагностичних або ремонтних робіт виконайте повну процедуру блокування/маркування енергоносіїв (Lockout/Tagout). Відключіть головний вимикач живлення електроприводу, закрийте запірну арматуру на пневматичній магістралі та встановіть попереджувальні таблички. Випустіть залишковий тиск із маслобака до 0 bar. Переконайтеся за манометром, що тиск повністю відсутній.

CAUTION - RISK OF BURNS: Components of the lubrication system, oil tank, pipelines and screw block heat up during operation to +90...+105 °C. Use personal protective equipment (PPE): heat-resistant gloves, safety goggles and long-sleeved protective clothing. Wait until the equipment has cooled down below +40 °C before opening the lubrication system or disassembling filters.

3. Required diagnostic tools

Tool Name Specification / Model Measurement range Purpose
Thermovisor / Thermal imager Fluke Ti400 or equivalent (emissivity ε=0.95) -20 °C ... +600 °C Non-contact temperature measurement of oil heat exchanger, thermostat, pipelines
Digital pressure gauge / Set of pressure gauges Accuracy class 0.6, resistant to oil 0 ... 25 bar Pressure drop measurement on the oil filter and separator
Laser Tachometer / Stroboscope Optris / Testo 10 ... 10000 rpm Checking the speed of the cooling fan
Anemometer / Flow speed meter Testo 410-2 0.4 ... 20 m/s Airflow Velocity Measurement Through the Heat Exchanger
Digital Multimeter Fluke 87V 0 ... 1000 V AC/DC, 0 ... 50 MOhm Checking of temperature sensor loops (Pt100 / Pt1000 / thermocouples)

4. Initial Assessment Checklist

Perform the following checks and record the parameters before disassembly or deep diagnostics:

Parameter / Observation Object Acceptable Limit (Acceptable) Threshold value (Alarm) Actual Result
Ambient temperature in the room +5 °C ... +35 °C (according to ISO 1217) > +40 °C [ ] Record
Oil level in the oil tank (in the stopped state after pressure reduction) Center of the viewing glass Below minimum / Above maximum [ ] Record
Pressure drop on the oil filter < 0.8 bar 1.5 bar [ ] Record
Pressure drop on the air-oil separator < 0.2 bar (new: ~0.1 bar) > 0.8 bar [ ] Record
Discharge pressure of the compressor According to the passport (for example, 7.5 bar or 10 bar) Deviation > 10% from setpoint [ ] Record
Availability of errors in the controller archive Missing Repeated Errors "High Discharge Temperature" [ ] Record

5. Systematic Diagnostic Scheme

Use this step-by-step algorithm for fault localization:

  1. Check operating mode and environmental conditions:
    • IF temperature in compressor > +40 °C or ventilation is blocked → Likely cause: Ventilation failure / overheating of incoming air. Check the exhaust fans of the room.
    • ELSE → Go to step 2.
  2. Thermographic inspection of the oil heat exchanger (radiator):
    • Measure the temperature of the tubes at the inlet and outlet of the radiator using an infrared thermometer.
    • If temperature difference between the inlet and outlet of the oil < 8 °C (at full load) → Probable cause: Contamination of the radiator plates/fin or bypassing of the oil (defective thermostat valve). Go to item 3.
    • If temperature difference is within normal range (15 ... 25 °C), and the discharge temperature is high → Likely cause: Insufficient cooling air flow through the radiator or internal wear of the fan unit. Go to item 5.
  3. Thermostatic valve operation check:
    • Measure the temperature of three thermostat ports with an infrared thermometer: line from the oil tank, line to the radiator, bypass to the oil filter.
    • IF line to the radiator remains cold or slightly warm at a temperature of > +90 °C → Likely cause: Sticking of the thermostat's thermoelement in the closed position.
    • ELSE → Go to step 4.
  4. Oil circulation loop check:
    • Check the level and condition of the oil in the oil tank. The oil should be clear, without signs of foaming or carbonization.
    • Check the pressure drop across the oil filter. If pressure drop > 1.5 bar → Likely cause: Oil filter clogging, restricting the supply of lubricant to the friction nodes and cooling.
  5. Temperature sensor check and control:
    • Compare the readings of the pressure sensor (Pt100) with the actual temperature of the compressor housing near the outlet, measured by a calibrated contact thermometer.
    • If the deviation exceeds ±3 °C → Probable cause: Sensor calibration drift or fault in the controller's measurement channel.

6. "Symptom - Cause - Diagnosis" Matrix

Symptom Likely causes (in order of likelihood) Diagnostic Test Expected result upon confirmation of the cause
High inlet temperature (> +105 °C) 1. Contamination of the oil radiator surface (dust, lint, grease deposits) Visual inspection of blades, measurement of temperature difference on the radiator with a thermal imager Small temperature difference (< 8 °C) between the inlet and outlet of the lubricant
2. Stemming of the thermocouple of the thermostat valve Temperature measurement of thermostat pipe during reaching operating mode Cold radiator pipe at hot thermostat housing
3. Low oil level in the oil reservoir Inspection of the viewing glass in the off and operating states Level below the permissible minimum, insufficient mass flow rate of oil for heat exchange
4. Non-standard properties / degradation of compressor oil Oil Condition Analysis (laboratory test for kinematic viscosity at 40°C/100°C, acid number TAN) Viscosity reduction, high content of oxidation products

7. Detailed Root Cause Analysis

7.1. Contamination of the oil heat exchanger (external and internal)

Чому це відбувається: Компресори всмоктують повітря з виробничих приміщень, що містить пил, волокна, аерозолі мастил. На ребрах повітряного боку теплообмінника утворюється щільна кірка, яка діє як теплоізолятор. З внутрішнього боку (масляний контур) можливе утворення лакових відкладень та шламу через перевищення термінів заміни олії або використання мастил низької якості, що не відповідають специфікаціям ISO DP.

How to confirm: The thermal imager detects high temperature on the collector at the heat exchanger inlet, but the tubes or plates remain cold or have an uneven temperature field along their entire length (presence of blockages).

Наслідки: Зменшення ефективності охолодження мастила призводить до перегріву гвинтової пари, зменшення зазорів у зачепленні роторів, ризику задирів і аварійного зупину.

7.2. Failure of the Thermostatic Valve

Why is this happening: The thermostatic element contains a wax filler that expands when heated. Under cyclic loads or upon entry of mechanical contaminants, the valve stem gets stuck. As a result, the oil circulates through the small circuit (bypassing the oil cooler) even when the intake temperature has reached the critical value.

How to confirm: Check the pipe leading to the radiator by hand or with an infrared thermometer. If the oil pump outlet temperature exceeds +80 °C and the radiator pipe is cold — the thermoelement is stuck.

Наслідки: Повне припинення охолодження олії в радіаторі, швидке зростання температури нагнітання до спрацьовування захисту.

7.3. Low oil level or use of degraded lubricant

Чому це відбувається: Витік через ущільнення, надмірне унесення олії через зношений сепаратор або несвоєчасне дозаправлення призводять до зменшення об'єму олії в системі. Менший об'єм циркулює частіше, не встигаючи віддавати тепло. Деградована олія втрачає свої теплопровідні та змащувальні властивості.

Як підтвердити: Оглядове скло маслобака показує низький рівень або повну відсутність олії під час роботи компресора. Аналіз олії показує перевищення кислотного числа (TAN) понад 2.0 мг KOH/г.

Наслідки: Голодування вузлів тертя, перегрів підшипників гвинтового блоку, прискорене зношування робочих поверхонь роторів.

8. Step-by-step troubleshooting procedures

Procedure 1: Oil Cooler Cleaning

  1. Perform the requirements of the safety section (LOTO, pressure release, cooling).
  2. Remove the protective covers of the compressor to access the radiator.
  3. For external cleaning (if contaminated with dust/mold): blow the blades with compressed air in the direction opposite to the usual cooling air flow (from bottom to top or from inside out), under a pressure not exceeding 2–3 bar. If there are grease deposits, apply a special industrial cleaning agent (non-aggressive to aluminum), let it act for 10–15 minutes, and rinse with warm water under low pressure.
  4. For internal cleaning (in case of lacquer formation): perform the oil circuit cleaning with special cleaning oil according to the compressor manufacturer's instructions.
  5. Assemble the unit, fill the system with fresh oil to the normal level.
  6. Post-repair check: Start the compressor on no load, then under load. Use an infrared thermometer to ensure that the temperature difference across the radiator is 12 ... 20 °C, and the discharge temperature has stabilized within +75 ... +90 °C.

Procedure 2: Replacement of the thermocouple of the thermostat valve

  1. Perform the LOTO procedure and relieve the pressure in the system.
  2. Remove the housing cover of the thermostat valve. Be careful: a small amount of hot oil remains in the internal cavity (use a collection container and cloth).
  3. Remove the retaining ring and the old thermocouple together with the spring and sealing rings (O-rings).
  4. Thoroughly clean the mounting surface from residue of sealant and deposits.
  5. Install a new original thermocouple (with nominal operating temperature according to the passport, for example, +71 °C or +75 °C). Replace all rubber sealing rings with new ones, lubricating them with clean compressor grease.
  6. Assemble the valve, tighten the cover bolts evenly (torque according to OEM specification, usually 25–35 Nm for M8 thread).
  7. Post-repair check: Start the compressor. Use a pyrometer or thermal imager to check the moment the pipe opens on the radiator when the thermoelement reaches the threshold temperature.

9. Preventive Maintenance

Primary Cause Preventive strategy Control Method Recommended interval
Radiator Contamination Air purity control in the compressor room, installation of pre-filter mats on the incoming ventilation of the room Visual inspection of radiator blades, monitoring of blower temperature Every 500 hours (or monthly)
Thermostat Wear Planned replacement of the thermoelement during comprehensive technical maintenance Thermal imaging inspection of thermostat hoses Every 4000–8000 hours (or 1 time per year)
Lubricant degradation Use of high-quality synthetic lubricants (polyalphaolefins / ethers) according to ISO 6743-3 (class DAH/DAJ) Laboratory oil analysis (viscosity, TAN, presence of water) Every 2000 hours (mineral) / 4000-6000 hours (synthetic)

10. Spare Parts and Components

For rapid restoration of the functionality of compressor equipment, use high-quality components from the e-catalogue UNITEC-D:

Description of the part Specification When to replace Category UNITEC-D
Thermocouple of the thermostat valve Setting +71 °C / +75 °C / +80 °C, resistant to synthetic oils When the temperature regime deviates or every 8000 hours Oil System Components
Oil filter assembly Filtering accuracy 10-25 micrometers, operating pressure up to 20 bar Every 2000 hours or when pressure drop > 1.5 bar Compressor filters
Air-oil separator Oil residue efficiency < 3 mg/m³ Every 4000 hours or when the pressure drop > 0.8 bar Air and Oil Separators
Thermostat housing seal kit (O-rings) Viton (FKM), resistance up to +150 °C At each disassembly of the thermostat Repair kits and seals

Select the required consumables and spare parts for your compressor directly in the e-catalogue UNITEC-D.

11. Normative References

  • ISO 1217: Volume compressors. Acceptance tests.
  • ISO 6743-3: Lubricants, industrial oils and related products (class D — compressors).
  • EN 1012-1: Compressors and vacuum pumps. Safety requirements. Part 1: Air compressors.
  • DSTU EN ISO 12100: Machine Safety. General Principles of Design. Risk Assessment and Risk Reduction.

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles

Diagnosis and elimination of high discharge temperature of the screw compressor

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Diagnosis and elimination of high discharge temperature of the screw compressor
Детальний інженерний посібник з пошуку та усунення несправностей гвинтових компресорів за симптомом високої температури нагнітання. Розглядаються перевірка рівня мастила, засмічення охолоджувачів, від

1. Description of the problem and scope

This manual is intended for reliability engineers and duty mechanics of industrial enterprises. It covers diagnostics and troubleshooting related to overheating of the oil-air mixture and high injection temperature at the exit of the screw compressor unit (air-end). The problem is critical for the uninterrupted operation of pneumatic networks at enterprises of the machine-building, food, chemical and energy industries.

Classification of the degree of danger: Critical condition (Alarm / Trip). Normal operating discharge temperature is between 75 °C and 90 °C. Reaching a threshold of 100 °C requires an immediate operator warning, and a 105-110 °C exceedance protection trip forces the unit to stop to prevent screw steam jamming and oil coking.

2. Precautions (Safety techniques)

CAUTION! DANGER OF BURNS AND HIGH PRESSURE

Before performing any diagnostic or repair work, perform the following procedures:

  • Lockout/Tagout (LOTO): Turn off the main compressor power switch completely, secure it with a padlock and post a warning sign in accordance with EN ISO 14118 requirements and applicable occupational health and safety regulations.
  • Reset the residual pressure: Make sure that the pressure gauge on the oil separator shows 0 bar. Slowly open the manual pressure relief valve. It is forbidden to open oil plug or flange connections under pressure above 0 bar.
  • Thermal hazard: The surfaces of the compressor unit, oil cooler and oil separator can heat up to 105 °C. Use heat-resistant protective gloves and overalls.
  • PPE: Safety glasses, shoes with metal toes, oil-resistant gloves.

3. Necessary diagnostic tools

Name of the tool Specification / Model Measurement range Purpose
Thermal imager Fluke Ti400 or analog (sensitivity < 0.05°C) -20°C ... +600°C Non-contact measurement of temperature distribution on the surface of radiators, lines and thermostat.
Digital thermometer (or thermocouple) Fluke 52 II (Type K) -200°C ... +1370°C Spot temperature measurement at the oil and air inlet/outlet nozzles.
Ultrasonic leak detector / pressure drop detection SDT270 or similar 20 kHz ... 100 kHz Checking the pressure drop on the oil filter and oil separator.
Manometric collector Analog/digital with accuracy class 1.0 0 ... 25 bar Control of oil pressure and system operating pressure.
Multimeter Fluke 87V 0 ... 1000V AC/DC, 0 ... 50 MΩ Checking the resistance of temperature sensors (Pt100 / PTC / NTC) and control circuits.

4. Initial examination checklist (Before starting diagnostics)

Parameter to check Normative value Actual Value (Write) Status (Normal / Deviation)
Compressor oil level in the sight glass (cold state) The middle or upper mark of the dipstick
Ambient temperature in the compressor room +5°C ... +40°C (according to passport data)
Pressure drop across the air filter < 0.03 bar (new: 0.01 bar, replacement at 0.05 bar)
Pressure drop across the oil filter < 0.5 bar (new: 0.2 bar)
The cleanliness of the oil/air cooler plates Absence of dust, dirt, oil deposits
Belt drive tension condition (if applicable) According to the OEM instructions (p deflection under load)

5. Systematic diagnostic block diagram (Search algorithm)

  • Symptom: High discharge temperature (> 100°C)
    • Step 1. Check the oil level in the oil separator (on a stopped and cooled compressor).
      • IF level below minimum → **Probable cause:** Lubricant leakage or heavy entrainment due to worn oil separator. Check the scavenge line.
      • IF level is normal → Go to Step 2.
    • Step 2. Conduct a thermal imaging examination of the combined radiator (oil and air cooler).
      • IF there is an uneven distribution of temperatures (cold zones alternate with hot ones) or a high temperature difference between the inlet and outlet of the lubricant from the cooler (> 25°C) → **Probable cause:** Clogging of the external lamellae or internal silting of the radiator.
      • IF the heatsink is evenly hot over the entire area → Go to Step 3.
    • Step 3. Check the operation of the thermostatic valve.
      • IF bypass line (direct to screw block) is hot and line to cooler remains cold at discharge temperature > 85°C → **Probable Cause:** Thermostatic element stuck in closed position.
      • IF the thermostat is functioning correctly (mixing the streams) → Go to Step 4.
    • Step 4. Analyze the environmental conditions and the room's ventilation system.
      • IF the temperature inside the compressor room exceeds +40°C or the exhaust louvers are blocked/insufficient air exchange → **Probable cause:** Insufficient ventilation of the room or recirculation of hot air.
      • IF ventilation is normal → Go to Step 5.
    • Step 5. Check the serviceability of the measuring devices and the mode of operation.
      • IF temperature sensor (Pt100) gives false data due to cable damage or oxidation of contacts or the compressor is operating in continuous pressure overload mode → **Probable cause:** Sensor/controller failure or exceeding nominal discharge pressure (> 10 bar instead of 8 bar).

6. Fault-Cause Matrix

Symptom Probable causes (in order of probability) Diagnostic test Expected result if the cause is confirmed
High injection temperature (> 100°C) 1. Clogging of radiator fins (external) Visual inspection with a flashlight, thermal imager. Temperature gradient on the surface of the cooler, significant dust layer.
2. Reduced level or degradation of lubricant Checking the level on the glass, analyzing the viscosity and acid number of the lubricant. The level is below normal; the oil has darkened, has a burning smell (high TAN).
3. Jamming of the thermostatic valve Measuring the temperature of the tubes before and after the thermostat with a pyrometer/thermal imager. The pipe to the radiator is cold, the injection is hot. The thermostat does not open at 80°C+.
4. Insufficient air exchange in the room Measurement of the temperature of the air at the suction of the compressor and the environment. Intake air temperature > +40°C. The fans work on the hood inefficiently.
5. Clogging of the oil filter Measuring the pressure drop before and after the oil filter with a manometer. The pressure drop exceeds 0.8 bar (when the norm is < 0.4 bar). Lubricant is not supplied in sufficient quantity.

7. Detailed root cause analysis (Root Cause Analysis)

7.1. External and internal contamination of the oil cooler

Why it occurs: In industrial environments (especially in cement factories, woodworking or metallurgy) the air is saturated with dust, fibers or aerosols. When the cooling air passes through the ribbed tubes of the combined radiator, aerosols settle on the surface of the lamellas, forming a dense insulating crust. Internal fouling occurs due to the use of low-quality lubricants or the mixing of different types of mineral and synthetic lubricants, which leads to thermo-oxidative destruction and the formation of varnish deposits on the inner walls of the tubes.

How to confirm: The thermal imager shows local hot spots at the outlet of the screw unit and a significant difference in air temperature before and after the radiator, which does not correspond to the calculated passport.

Consequences: Reduction of the heat transfer coefficient, constant overheating of the lubricant, accelerated evaporation of light fractions of the lubricant, coking of the shaft seals and failure of the screw block bearings.

7.2. Failure (jamming) of the thermostatic valve

Why it occurs: The thermostatic element contains a paraffin or wax filler that expands when heated. When wear products, sludge or frequent cyclical temperature changes occur, the valve stem is deformed or loses its tightness, remaining in a closed state. The oil circulates along a short circuit (bypass), bypassing the radiator.

How to confirm: Even when the discharge temperature reaches 90°C, the pipe leading to the oil cooler remains cold or barely warm, while the bypass line is hot.

Consequences: Complete lack of cooling of the lubricant through the radiator, rapid temperature rise and emergency shutdown of the compressor by the controller.

7.3. Low level or critical aging of the lubricant

Why it occurs: Untimely replacement of lubricant, the presence of leaks in the connections or wear of the separator of the oil separator lead to a decrease in the volume of lubricant in the system. The grease performs not only the function of lubrication, but also takes away up to 80% of the heat of compression. A smaller amount of lubricant does not have time to remove heat from the screw pair.

How to confirm: Visual control of the oil gauge (below the minimum on a stopped unit), the presence of traces of lubricant in the exhaust air (lubricant mist in the pneumatic network).

Consequences: Oil starvation of bearings, burrs on screw rotors, critical overheating.

8. Step-by-Step Resolution

Procedure 1: Cleaning and flushing the oil cooler

  1. Perform full lockout and tagout (LOTO) procedure, verify no pressure (0 bar).
  2. Remove the compressor guards to gain access to the radiator.
  3. For external cleaning: blow the lamellas with compressed air in the direction of the reverse movement of the cooling air (from the inside to the outside), or use a special washing solution for aluminum heat exchangers with a neutral pH (5-8). It is forbidden to use metal brushes or high-pressure washers with excessive pressure (> 4 bar) in order not to damage the thin aluminum lamellas.
  4. For internal cleaning (in case of silting): connect a service flushing station, pump a special chemical solution to remove scale and oil deposits according to the heat exchanger manufacturer's instructions. Rinse with clean water and blow with compressed air.
  5. Assemble the assembly in reverse order, replacing the sealing rings (O-rings) with new ones.
  6. Verification after repair: Run the compressor at idle, then under load. Use a thermal imager to check the uniformity of radiator heating. The temperature difference between the inlet and outlet of the lubricant from the cooler should be 8°C ... 15°C.

Procedure 2: Replacing the thermostatic element

  1. Perform the LOTO procedure, depressurize the system, drain the oil from the thermostat housing into a special container.
  2. Remove the retaining ring or unscrew the cover of the thermostatic valve body.
  3. Remove the old thermostatic element and spring. Clean the inner cavity of the housing from the remains of sealant and dirt.
  4. Install a new original thermostatic element (with a rated opening temperature eg 71°C or 75°C depending on OEM specification) together with new seals.
  5. Close the cover, tighten the mounting bolts with a torque wrench to the torque according to the manufacturer's instructions (usually 22-25 Nm for an M8 thread).
  6. Fill the system with recommended compressor oil to level.
  7. Verification after repair: Perform a test run. Check the temperature of the tubes at the outlet of the thermostat using a digital thermometer. When the thermostat opening temperature is reached, the radiator tube should begin to heat up.

9. Preventive Measures

The root cause Prevention strategy Monitoring method Recommended interval
Clogged radiator Installation of filter mats on intake shutters of the compressor, regular blowing. Weekly visual control and temperature drop check. Every 250 - 500 hours of operation
Lubricant degradation Use of high-quality synthetic lubricants (PAO / Ester), compliance with the replacement regulations. Laboratory analysis of lubricant (viscosity, TAN acid number, water content). Every 2000 – 4000 hours (or once a year)
Thermostat wear Scheduled replacement of the thermostatic element together with the oil filter. Injection temperature control on the control panel. Every 8000 hours or once a year
Low oil level Daily inspection before starting shifts. Level control through the sight glass. Every day

10. Spare parts and components

For quick restoration of compressor equipment, use proven components from the UNITEC-D catalog:

Description of the part Specification When to replace Category UNITEC
Thermostatic element (71°C / 75°C) Compatible with Atlas Copco, Kaeser, Ingersoll Rand Every 8000 hours or when jammed Compressor thermostats
Fine cleaning oil filter Threaded cartridge, rating 10 micron, Pmax 20 bar Every 2000 hours or when the pressure drops > 0.5 bar Filters for compressors
Compressor synthetic lubricant ISO VG 46 / 68 (PAO-base, resource 4000-8000 hours) According to the regulation or analysis of the lubricant Industrial lubricants
Oil separator kit (Separator element) Coalescent element of deep cleansing Every 4000 hours or at u > 0.8 bar Air/oil separators

Get acquainted with the complete assortment and select the necessary components in our electronic catalog UNITEC-D.

11. Regulatory references and documentation

  • ISO 1217: Volumetric compressors. Acceptance tests.
  • EN ISO 14118: Machine safety. Protection against unauthorized start-up (Locking/Marking).
  • EN 1012-1: Compressors and vacuum pumps. Security requirements. Part 1: Air compressors.
  • Technical documentation and service manuals of the leading OEM manufacturers of screw compressors.
  • UNITEC-D GmbH internal maintenance guides (Maintenance Guides).

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles

Diagnosis and resolution of high discharge temperature of a screw compressor

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Diagnosis and resolution of high discharge temperature of a screw compressor
Покроковий керівник з діагностики та усунення високої температури нагнітання у гвинтових компресорах. Розглядаються несправності термостата, забруднення охолоджувачів, рівень мастила та деградація рід

1. Problem Description and Area of Application

High temperature of the lubricating air mixture in screw compressors is a critical operating deviation, leading to oil coking, loss of its viscosity, premature bearing wear, deformation of screw rotors, and emergency shutdown of the equipment upon temperature sensor signal.

Application area: Industrial oil-lubricated screw compressors (power from 15 kW to 350 kW) on enterprises in the machinery, food, chemical and energy sectors in Ukraine.

Criticality classification:

  • Нормальна температура нагнітання: від +75 °C до +90 °C.
  • Alarm: from +98 °C to +105 °C (check and diagnostics within 24 hours).
  • Critical failure (Trip): over +105 °C — +105 °C (immediate blocking of start and emergency shutdown of equipment according to the requirements ISO 1217 and EN 1012-1).

2. Precautionary Measures (Safety Techniques)

WARNING! RISK OF BURNS AND HIGH PRESSURE!

Before starting any diagnostic or maintenance work, perform the following mandatory actions:

  • Lockout/Tagout (LOTO): Fully turn off the main power switch of the compressor's electrical supply, install a lock and a warning tag. Check for absence of voltage using a digital multimeter.
  • Pressure release: Make sure the pressure gauge on the separator shows 0 bar. Slowly open the manual drain valve to release any remaining pressure in the system. Do not open the fill plugs or flanges under pressure.
  • Hot surfaces: The temperature of the compressor unit elements, oil cooler and oil lines may exceed +95 °C. Use heat-resistant protective gloves and special clothing (PPE according to standards EN 388 and EN 407).
  • Chemical Hazards: Use safety goggles and rubber gloves when working with compressor oil and chemical cleaners for heat exchangers (according to the safety data sheet MSDS of the oil).

3. Required diagnostic tools

For accurate fault localization, use trusted and calibrated equipment according to metrology standards:

Tool Name Technical specification / Model Measurement range Purpose
Thermal imager Fluke Ti401PRO / Testo 883 -20 °C ... +650 °C Detection of local overheating zones of lubrication lines, thermostat and radiator
Digital multimeter Fluke 87V / Keysight U1273A 0 ... 1000 V AC/DC, 0 ... 50 MΩ Resistance check of temperature sensors (Pt100 / Pt1000) and control circuits
Non-contact thermometer (Pyrometer) Testo 835-T2 -30 °C ... +600 °C Quick measurement of temperature at the input/output of the thermostat and cooler
Differential manometer Keller Leo 2 / Testo 512 0 ... 10 bar Pressure drop measurement on the oil filter and oil separator
Anemometer / Air Speed Meter Testo 410-2 0 ... 20 m/s Control of the volume flow rate of cooling air through ventilation ducts

4. Initial Inspection Checklist

Fill out this form BEFORE disassembling the units or switching off the compressor (in case of controlled start-up):

Parameter for checking Measurement method / Source Allowable value Actual value
Oil level in the gear box Visually via the overview display (operating mode / stopped state) Observation window (after 5 min. stop) [   ]
Ambient temperature in the room Thermometer near the compressor air inlet +5 °C ... +40 °C (according to DIN EN ISO) [   ]
Working pressure of injection Pressure gauge on the control panel According to the passport (for example, 7.0 - 10.0 bar) [   ]
Pressure drop on the oil filter ΔP for pressure gauges or controller < 0.8 - 1.0 bar (new: < 0.3 bar) [   ]
Pressure drop across the oil separator (separator) Pressure drop between the oil tank pressure and the separator outlet pressure < 0.8 bar (alarm at > 1.0 bar) [   ]
Surface finish of the oil cooler Visual inspection of radiator ribs Clean blades, without dust and grease layer [   ]

5. Systematic Diagnostic Block Diagram

Use this step-by-step algorithm for fault detection:

  • STEP 1. Checking external conditions and ventilation
    • IF temperature in the room > +40 °C OR ventilation louvers are blocked/dirty -> Cause: Air exchange disruption in the compressor room. Check the exhaust ventilation and the condition of the air filters in the cabin.
    • Else -> proceed to Step 2.
  • КРОК 2. Контроль температури на маслоохолоджувачі
    • За допомогою пірометра виміряйте температуру мастила на вході та виході з радіатора.
      • IF трубки радіатора холодні або мають різницю температур менше ніж 10-15 °C на вході/виході при гарячій магістралі -> Причина: Зовнішнє або внутрішнє забруднення охолоджувача, або термостатичний клапан заклинив у закритому положенні. Перейдіть до КРОКУ 3.
      • If tubes are hot over the entire area, but the air flow is weak -> Cause: Clogged radiator fins or malfunction of the cooling fan.
  • STEP 3. Thermostatic Valve Diagnosis
    • Measure the temperature of the three thermostat ports (oil tank line, radiator line, and report line to the screw block).
      • IF bypass line (direct to the block) is hot, and the radiator line is cold at an intake temperature above +85 °C -> Cause: Thermostatic element has lost its seal (bellows is broken) or is stuck. Proceed to STEP 4.
  • КРОК 4. Перевірка рівня та якості мастила
    • Перевірте рівень та стан мастила через оглядове скло.
      • IF рівень мастила нижче мінімуму -> Причина: Витік мастила або надмірне виносу через зношений масловідділювач.
      • If the grease darkens, has a burnt smell or contains sediment -> Cause: Grease degradation due to exceeding the replacement interval or mixing incompatible greases.
  • STEP 5. Hydraulic resistance check of the oil circuit
    • Check the pressure drop across the oil filter.
      • IF ΔP > 1.0 bar -> Cause: Contamination of the paper element of the oil filter.

6. "Symptom - Cause - Diagnostic Test" Matrix

Symptom Likely causes (in order of likelihood) Diagnostic Test Expected result upon confirmation of the cause
Rapid temperature rise to the emergency level (> +105 °C) within 5-10 min after start-up 1. Stuck thermostat in closed position
2. Low lubricant level
3. Blocked cooling water supply (for water cooling)
Measure the temperature of the line before/after the radiator with a pyrometer; check the inspection glass Coolant line is cold; oil level is below minimum; water consumption is zero
Gradual (over weeks) rise of working temperature to +95...+102 °C 1. Contamination of the air radiator fins with dust/oil
2. Fouling of the water heat exchanger with scale
3. Degradation (aging) of the compressor oil
Inspection of lamellas by thermal imager or visually; checking of oil analysis for acid number (TAN) Uneven temperature field on the radiator; high value of TAN (> 2.0 mg KOH/g)
Periodic overheating at maximum load during the summer period 1. High temperature in the room (> +40 °C)
2. Insufficient air exchange in the ducts
3. Worn oil filter (partially clogged)
Measure the air velocity with an anemometer; remove ΔP of the oil filter Air velocity in the exhaust duct is below design; ΔP filter > 1.2 bar

7. Root Cause Analysis

7.1. Low level of oil in the oil tank

Why it occurs: Wear of the oil separator (separator) causing droplet or mist-like oil carryover into the pneumatic network, or presence of external leaks through seals, flanges, high-pressure hose connections.

How to confirm: Inspection of oil level on a stopped compressor (after 10 minutes of shutdown). Check of pipes for presence of oil traces. Control of presence of oil in the main air receiver.

Наслідки: Зменшення об'єму мастила знижує теплоємність системи охолодження. Мастило не встигає відводити тепло від гвинтової пари, що веде до масляного голодування підшипників, їх заклинювання та руйнування ущільнень роторів.

7.2. Contamination of the oil cooler (radiator) surface

Why it occurs: Dust, lint, and technological aerosols are sucked in through the compressor cabin air filters. In metalworking and woodworking shops, the lamellas become clogged with fine swarf mixed with lubricant dust.

Як підтвердити: Сканування тепловізором поверхні радіатора. Наявність темних зон з підвищеною температурою або повна відсутність градієнту температур на окремих секціях свідчить про заблоковані повітряні канали.

Наслідки: Падіння ефективності теплообміну між мастилом та охолоджуючим повітрям. Компресор переходить у постійний температурний режим з перевищенням номінальних допусків.

7.3. Failure of the Thermostatic Valve

Why it occurs: Metal fatigue of the thermosensitive element (bellows), formation of deposits (sludge and lacquers) on the valve stem, preventing its free movement.

Як підтвердити: Вимірювання температур трьох точок термостата. Якщо температура нагнітання висока (+98 °C), а лінія до радіатора залишається холодною — термостат заклинив і мастило циркулює лише в обхід охолоджувача (через байпас).

Наслідки: Повне припинення подачі мастила через маслоохолоджувач. Увесь об'єм гарячого мастила повертається безпосередньо у впорскування гвинтового блока, що викликає аварійне вимкнення за перегрівом протягом кількох хвилин.

7.4. Degradation of Compressor Oil

Why it occurs: Exceeding the scheduled oil change interval (for example, more than 4000-8000 hours depending on the type of base oil — mineral or synthetic), operation at constant overheating, which accelerates the oxidation and polymerization of the oil.

How to confirm: Oil sample taking and laboratory analysis for kinematic viscosity (at +40 °C and +100 °C), total acid number (TAN) and presence of water.

Наслідки: Зниження в'язкості мастила при високих температурах, утворення лакових відкладень на поверхнях регулюючих клапанів, золотників та прецизійних зазорах гвинтової пари.

8. Step-by-step troubleshooting procedures

Procedure A: Replacement and Inspection of the Thermostatic Element

  1. Perform the procedure Lockout/Tagout (LOTO) and release the pressure in the system to 0 bar (see section 2).
  2. Remove the thermostat housing cover using a torque wrench (the tightening torque of the bolts depends on the model, usually 25-35 Nm).
  3. Remove the retaining ring and the thermostat element (cartridge).
  4. Clean the internal cavity of the housing from residues of old grease and deposits using a special cleaner (for example, technical alcohol or a solvent without acetone).
  5. Perform the thermostat test: submerge the new or removed cartridge into a water container and heat it, monitoring the temperature with a thermometer. The stem should start to lift at the opening temperature indicated on the body (for example, +71 °C or +78 °C), and fully extend by 8-10 mm upon reaching the full opening temperature (+85 °C).
  6. Install a new sealing set (O-ring) and a new thermostat element. Lubricate the seal with clean compressor oil.
  7. Assemble the node in reverse order, tightening the cross bolts crosswise with the torque according to the manufacturer's instruction.
  8. Верифікація: Запустіть компресор без навантаження, перевірте герметичність з'єднань і простежте за градієнтом температур на радіаторі за допомогою пірометра.

Procedure B: Cleaning the Oil Cooler Surface

  1. Disconnect the compressor (LOTO) and close the shut-off valve on the consumer line.
  2. Remove the protective covers and ducts that provide access to the finned surface of the radiator.
  3. For air cleaning: apply low-pressure compressed air blowing (no more than 2-3 bar) in the direction opposite to the normal flow of cooling air (from inside out), to dislodge dirt from the fins.
  4. For persistent oil contamination: apply a special non-aggressive alkaline cleaning agent for heat exchanger cleaning using a sprayer. Allow exposure for 10-15 minutes, preventing the chemical from drying out.
  5. Rinse the solution with warm water (temperature not exceeding +50 °C) under pressure not exceeding 4-5 bar, avoiding damage to the thin aluminum fins of the heat exchanger.
  6. Dry the surface with an air stream.
  7. Верифікація: Зробіть термозйомку радіатора під час робочого навантаження. Поле температур має бути рівномірним, перепад температур мастила на вході та виході має становити не менше 12-18 °C.

9. Preventive Measures

Primary Cause Preventive strategy Monitoring method Recommended interval
Radiator Contamination Regular cleaning of blades, installation of pre-filters on intake ventilation of the compressor room Temperature differential control and monthly visual inspection Every 500 – 1000 hours (or monthly in dusty conditions)
Thermostat Wear Planned replacement of the thermostatic element together with a sealing kit Control of intake temperature on the control panel Every 8000 – 12 000 hours (or 1 time per year)
Lubricant degradation Use of original synthetic oils, compliance with operating conditions Laboratory oil analysis (TAN, viscosity, water) Every 2000 hours (mineral) / 4000-6000 hours (synthetic)
Increase in filter resistance Timely replacement of oil filters and separators Control of differential pressure (ΔP) by manometers Every 2000 hours (or when ΔP > 1.0 bar)

10. Spare Parts and Components

Description of the part Technical specification When to replace Category UNITEC
Thermostatic element (Cartridge) Opening temperature +71°C ... +82°C, brass/stainless steel When the temperature regime deviates or every 8000 hours Oil System Components / Thermostats
Oil filter (screw-in) Filtering accuracy 10-25 microns, working pressure up to 16 bar Every 2000 hours or when ΔP > 1.0 bar Compressor filters
Mass flow meter (Separator) Deep cleaning element, lubricant residue < 3 mg/m³ Every 3000-4000 hours or when the grease is removed Air/Oil Separator
Compressive synthetic lubricant ISO VG 46 / VG 68, synthetic base (PAO / Diester) According to the results of the analysis or every 4000-8000 hours Industrial lubricants
Sealing kit (O-rings) FKM (Viton) / NBR, heat resistance up to +150 °C At each disassembly of units or replacement of thermostat Seals and Repair Kits

Full range of certified spare parts for industrial compressors from European and world manufacturers is available in our electronic catalog. Visit electronic catalog UNITEC-D for selecting equivalents and placing an order.

11. Normative References and Documentation

  • ISO 1217: Volume compressors. Acceptance tests.
  • EN 1012-1: Compressors and vacuum pumps. Safety requirements. Part 1: Air compressors.
  • DIN 51506: Lubricants for compressors. Requirements for lubricants grades VB, VC, VBL, VCL, VD.
  • ISO 4406: Continuous Hydraulics. Method of coding the fluid cleanliness level.
  • Technical documentation from compressor equipment manufacturers (Atlas Copco, Kaeser, Ingersoll Rand, Gardner Denver).
  • Internal Technical Maintenance Instructions UNITEC-D GmbH (Maintenance Guide Series #UT-COMP-04).

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles

Diagnosis and elimination of high discharge temperature of the screw compressor

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Diagnosis and elimination of high discharge temperature of the screw compressor
Детальний посібник з діагностики та усунення високої температури нагнітання гвинтових компресорів. Розглядаються рівень мастила, стан радіаторів, термостат та умови довкілля.

1. Description of the problem and scope of application

This manual is intended for senior maintenance engineers, diagnosticians and mechanics of Ukrainian industrial enterprises. The document defines the algorithm for finding and eliminating faults for oil-filled screw compressors (power from 30 to 250 kW) operating under conditions of increased heat load.

Classification of the criticality of the accident:

  • Critical (Class A): The discharge temperature at the exit of the screw unit reaches or exceeds 110 °C. The compressor stops after the emergency protection signal (Trip). Risk of coking of the lubricant, jamming of the screw pair and destruction of seals. Requires immediate intervention before restart.
  • Warning level (Class B): Discharge temperature is 100-109 °C for more than 15 minutes. Lubricant viscosity decrease, risk of protection tripping. Diagnostics required during the nearest technological window.
  • Normal operating range: 75–95 °C (depending on the type of lubricant and environmental conditions).

The manual covers the analysis of four main sources of malfunctions: the condition of the lubrication level and oil quality, contamination of the heat exchangers (oil and air), failure of the thermostatic valve, and the influence of environmental parameters on the compressor station.

2. Precautions and safety

CAUTION! HIGH PRESSURE AND TEMPERATURE HAZARD

Lockout/Tagout (LOTO): Before performing any mechanical work or removing components, completely de-energize the compressor station, install padlocks (Padlock) on the main switch and check the absence of voltage with a multimeter. Make sure the system has completely depressurized to 0.0 bar on the oil separator manometer.

Personal protective equipment (PPE): Mandatory use of heat-resistant gloves (protection from hot surfaces up to 120 °C), protective glasses, overalls made of fire-resistant materials and protective shoes with metal toes.

Hazards from stored energy: Oil and propeller housing components remain hot for a long time after stopping. Do not open oil filler holes or filters until the system has cooled below 40 °C. Danger of ejection of hot grease under residual pressure.

3. Necessary diagnostic tools

Name of the tool Specification / Model Measurement range Purpose
Thermal imager Fluke Ti400 or analog (sensitivity < 0.05°C) -20 °C ... +650 °C Detection of local overheating zones of the oil radiator, thermostat, lines and bearings.
Digital thermometer with thermocouple (Type K) Testo 925 or similar -50 °C ... +1000 °C Measurement of the actual temperature at the inlets/outlets of the oil cooler and discharge.
Differential manometer Keller Leo 3 or similar 0 ... 10 bar Measuring the pressure drop on the oil filter and oil separator.
Anemometer / Air speed meter Testo 410-1 0.4 ... 20 m/s Air flow control through the ventilation ducts and compressor radiator.
Digital multimeter Fluke 87V 0 ... 1000 V AC/DC, 0 ... 50 MOhm Checking the circuits of temperature sensors (Pt100 / PTC) and power supply of cooling fans.

4. Initial condition assessment checklist

Complete this table directly at the facility BEFORE disassembly or in-depth diagnostics:

Parameter / Observation Normal value Actual Value (Write) Status (Normal / Deviation)
Injection working pressure 7.0 – 10.0 bar
Injection temperature at the outlet of the block 78 - 92 °C
Oil level in the sight glass (at a stop / running) The middle of the window / 1/2 - 3/4
Air temperature in the compressor room +5 °C ... +40 °C
Pressure drop on the oil filter < 0.8 bar (clean)
Controller crash history (Log) No frequent codes A-03 (High Temp)
The date of the last oil and filter change Less than 2000–4000 hours (according to regulations)

5. Step-by-step diagram of diagnostics (Decision-making tree)

  1. Symptom: Discharge temperature above 105 °C.
    • Step 1.1: Check the oil level in the receiver-oil separator.
      • If the level is below the minimum mark: The probable cause is an oil leak or excessive carry-out due to a worn separator. Go to section 7.1.
      • If the level is normal or high: Go to Step 1.2.
    • Step 1.2: Perform a thermal imaging inspection of the combination radiator (oil/air).
      • If there is a sharp temperature difference in sections or an average temperature of more than 85 °C at the entrance to the thermostat and mains: Contamination of the ribs or internal channels of the radiator. Go to section 7.2.
      • If the radiator is only partially hot or the bypass line is hot: Go to Step 1.3.
    • Step 1.3: Check the operation of the thermostatic valve with a non-contact pyrometer or thermocouple on the three connections (from the unit, to the radiator, from the radiator).
      • If the nozzle on the cooler remains cold when the oil reaches 80 °C: The thermostat is stuck in the closed position. Go to section 7.3.
      • If the thermostat is working correctly: Go to Step 1.4.
    • Step 1.4: Analyze the environmental conditions and ventilation of the room.
      • If the room temperature is above +40 °C or the exhaust ducts are blocked: Insufficient air exchange. Go to section 7.4.

6. Matrix of malfunctions and causes

Symptom Probable causes (in order of probability) Diagnostic test Expected result when confirming the cause
Rapid rise in temperature after start-up (< 15 min) 1. Thermostat jamming (Closed)
2. Critically low oil level
3. The radiator oil supply valve is blocked
Temperature measurements at the inlet/outlet of the thermostat with a pyrometer The line to the radiator is cold, the bypass line is hot. ΔT between nozzles > 25 °C.
A gradual increase in temperature over the course of weeks 1. External contamination of the radiator with dust/fluff
2. Internal coking of the radiator
3. Degradation of lubricant properties
Visual inspection of the ribbed surface and measurement of air flow / oil pressure drop A thick layer of dust on the slats, a decrease in the speed of the blowing air at the exit < 2.5 m/s.
Overheating during peak loads in summer 1. Insufficient ventilation of the compressor room
2. Indoor air temperature is too high (> 42 °C)
3. Failure of the axial blower fans
Measurement of indoor temperature and current consumption of fan motors The temperature in the room is above +40 °C, the fans are not switched on synchronously.
Periodic overheating with the presence of foam in the lubricant 1. Mixing incompatible lubricants
2. The resource of antifoam additives has been exhausted
3. Clogging of the oil filter
Analysis of oil samples in the laboratory (water content, viscosity, TAN) The presence of mechanical impurities, a high oxidation rate, a change in the color of the lubricant.

7. Analysis of the root causes of each malfunction

7.1. Low oil level and degradation of the lubrication system

Why this happens: The oil in a screw compressor performs three critical functions: lubricating the bearings, sealing the gaps between the rotors, and cooling (removing up to 80% of the heat energy of compression). When the oil level drops, the volume of the circulating coolant decreases, which leads to the rapid accumulation of heat in the limited mass of oil and metal of the block.

How to confirm: Check the level on a stopped and running compressor. Analyze the pressure drop on the oil filter (if ΔT > 1.0 bar, the filter is partially clogged with wear products). Check the condition of the oil separator for fluid leakage through the air line.

Consequences of inactivity: Burrs on the working surfaces of the screws, failure of rolling bearings due to oil starvation, thermal destruction of oil seals and complete jamming of the compressor pair.

7.2. Contamination of the air-oil heat exchanger

Why this happens: In the conditions of industrial enterprises of Ukraine, the intake air and cooling air contain dust, technological emissions, oil mist. Passing through the lamellas of the radiator, these particles settle on the surface, creating a heat-insulating layer. Varnish deposits form inside the radiator tubes when oil change intervals are exceeded.

How to confirm: Use a thermal imager. On a working radiator, the temperature difference between the inlet and outlet of the lubricant should be 15–25 °C. When the surface is contaminated, the thermogram shows local hot spots with minimal heat exchange at the edges or the entire perimeter.

Consequences of inactivity: Constant operation of the compressor at extreme temperatures, rapid degradation of lubricant additive packages (thermal cracking), activation of the emergency sensor and production stoppage.

7.3. Failure of the thermostatic valve

Why this happens: The thermostatic element contains a wax filler that expands when heated, moving the spool and directing the oil flow through the radiator or bypass directly into the block. Due to hydraulic shocks, contamination or natural wear and tear, the valve armature jams.

How to confirm: Use a pyrometer to measure the temperature of three points: the port from the oil tank, the port to the radiator, the port from the radiator (mixing). If the port on the radiator is cold, when the oil at the inlet is already above 85 °C, the element is jammed.

Consequences of inactivity: Lubricant circulation in a small circle without cooling. The temperature rises rapidly to the emergency mark within a few minutes of starting under load.

7.4. Problems of ventilation and environmental conditions

Why this happens: Compressor stations are often installed in closed rooms without forced supply and exhaust ventilation or with insufficient area of air intake grilles. The ban on the free emission of hot air to the outside leads to the recirculation of hot air inside the room.

How to confirm: Measure the air temperature directly before the air intake of the compressor. If it exceeds +40 °C, the cooling efficiency will drop critically, regardless of the health of the compressor itself.

Consequences of inaction: Permanent heat removal is difficult, the compressor operates in chronic overheating mode, which leads to a reduction in the service life of electronics, belts, hose connections and the engine itself.

8. Step-by-step troubleshooting procedures

Procedure A: Replacing and calibrating the thermostatic valve

  1. Do the full LOTO procedure (turn off the power, make sure there is no pressure of 0.0 bar).
  2. Remove the cover of the thermostatic valve body using a socket wrench of the appropriate size.
  3. Remove the old thermostatic element and O-rings.
  4. Thoroughly clean the seat from sealant residues and carbon deposits using a special cleaner and a lint-free cloth.
  5. Install a new original thermostatic element (with a nominal opening temperature of usually 71 °C or 75 °C). Replace all rubber seals with new ones, having previously lubricated them with clean compressor oil.
  6. Assemble the assembly in reverse order. Tighten the cover bolts crosswise to the torque recommended by the manufacturer (for standard M8 flanges - 25 Nm).
  7. Carry out a test run without load (in idle mode), monitoring the injection temperature and the opening of the line to the radiator with a pyrometer.
  8. Procedure B: Cleaning the air-oil radiator

    1. Perform the LOTO procedure and wait for the unit to cool below 40 °C.
    2. Remove the protective covers and air flow guides around the radiator.
    3. External cleaning: Blow the fins of the radiator with compressed air under a pressure of no more than 3-4 bar in the direction opposite to the normal flow of air (from the inside to the outside). In case of greasy stains, apply a professional solvent (non-aggressive to aluminum), leave for 10 minutes and rinse with warm water under low pressure (< 5 bar). Do not use metal brushes to avoid damaging the thin aluminum slats.
    4. Internal flushing (if necessary): Connect a mobile oil circuit flushing station using a special soft flushing grease or solvent to remove varnish deposits. Circulate the liquid for 2-3 hours at 50 °C.
    5. Assemble the casings, check the tightness of the joints, bring the oil level up to normal.
    6. Perform a trial run under load and record the operating temperature after 30 minutes of operation (norm: 80-90 °C).

    9. Preventive measures

    The root cause Prevention strategy Monitoring method Recommended interval
    Contamination of the radiator Regular blowing with compressed air and monitoring the condition of the air intake filters in the room. Visual inspection of ribs, control of temperature difference (ΔT). Monthly (or every 500 hours)
    Wear of the thermostatic element Planned preventive replacement of the thermostat together with lubricant and filters. Thermographic control of nozzles after start-up. Every 8000 hours or once a year
    Lubricant degradation Use of high-quality synthetic oils (polyalphaolefins / ethers) with acid number (TAN) control. Laboratory analysis of oil samples. Every 4000-6000 hours
    Violation of the microclimate in the room Modernization of supply ventilation, installation of exhaust fans with air temperature sensors. Ambient air temperature sensors in the compressor room. Continuous (automated control)

    10. Spare parts and components

    Use proven components to quickly restore compressor equipment. Reliable consumables and spare parts are available in the UNITEC-D GmbH catalog.

    Description of the part Specification When to replace Category UNITEC
    Thermostatic element (Valve) Opening temperature 71°C / 75°C / 80°C, threaded or cartridge type When jamming or every 8000 hours Thermostatic valves and repair kits
    Fine cleaning oil filter Filtration rating 10–25 microns, working pressure up to 20 bar Every 2000-4000 operating hours Compressor oil filters
    Air/Oil Separator element Residual oil content < 3 mg/m³, high heat resistance With increased oil removal or pressure ΔT > 1.0 bar Oil separators
    Compressor synthetic lubricant ISO VG 46 / VG 68 (PAO / Ester base) According to the results of the analysis or once a year Compressor oils and fluids
    Combined cooling radiator Aluminum plate-ribbed block for a specific model In case of mechanical damage or internal breakdown Cooling systems and radiators

    Select the necessary components and place an order directly in the electronic catalog: https://www.unitecd.com/e-catalog/

    11. References and regulatory framework

    • ISO 1217: Volumetric compressors — Acceptance test.
    • ISO 2151: Compressors and vacuum pumps - Noise measurement requirements.
    • DSTU EN 1012-1: Compressors and vacuum pumps. Security requirements. Part 1. Air compressors.
    • DSTU EN ISO 13849-1: Safety of machines and mechanisms. Safety-related details of control systems.
    • Technical documentation and operating instructions of the leading OEM manufacturers of screw compressors (Atlas Copco, Ingersoll Rand, Kaeser, Gardner Denver).
    • Related UNITEC-D manuals: "Diagnostics of vibration of screw units", "Analysis of the causes of premature failure of oil separators".

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles

Diagnosis and resolution of high discharge temperature of a screw compressor

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Diagnosis and resolution of high discharge temperature of a screw compressor
Покроковий технічний посібник з діагностики та усунення високої температури нагнітання у гвинтових компресорах. Аналіз стану олії, термостата, радіаторів та вентиляції з урахуванням європейських станд

1. Problem Description and Area of Application

This manual is intended for field engineers and technical service personnel of Ukrainian industry. It covers systematic diagnosis and elimination of faults related to critical increase in temperature of the oil-air mixture in oil-filled screw compressors.

Equipment to be serviced: Industrial oil-lubricated screw compressors with power from 15 to 315 kW with air and water cooling.

Criticality classification:

  • Critical (Emergency Stop): Suction temperature exceeds 105°C. Risk of oil coking, damage to the screw block seals and rotor jamming.
  • High (Warning): Inlet temperature is 98°C – 104°C. Immediate intervention is required during planned shutdown.
  • Small: Temperature is 90°C – 97°C under normal ambient conditions. Requires monitoring and checking of the heat exchanger cleanliness.

2. Precautionary Measures

WARNING! SAFETY FIRST!

Lockout/Tagout (LOTO): Before performing any work on disassembling cooling or lubrication circuits, completely turn off the compressor power supply at the main distribution panel and install lockout devices (LOTO). Ensure there are no residual electrical charges on the frequency converters and capacitors.

Energy saved under pressure: The hydraulic system and pneumatic circuit are under pressure up to 10-13 bar. It is prohibited to open the oil tank cap or connections until the pressure in the system is fully released to 0.0 bar according to the pressure gauge.

Hot surfaces: The temperature of the lubricant cooling elements and the screw blocks' housings reaches 100°C and above. Use personal protective equipment (PPE): heat-resistant gloves, safety goggles, and protective clothing.

Chemical Hazards: Used compressor oil irritates the skin and eyes. Avoid contact with hot oil and use oil-resistant gloves when servicing filters.

3. Required Diagnostic Tools

Tool Name Specification / Model Measurement range Purpose
Digital Multimeter Fluke 87V or equivalent (True RMS) 0 – 1000 V AC/DC, 0 – 50 MΩ, 0 – 400 mA Temperature sensor checks (Pt100/Pt1000), control circuits and power supply.
Thermal imager Fluke Ti401PRO / Testo 883 -20°C ... +650°C (sensitivity < 0.05°C) Detection of radiator restriction zones, thermostat sticking and bearing overheating.
Differential manometer DT-8890 or equivalent 0 – 2 bar (accuracy ±0.3%) Pressure drop measurement on oil and air filters, oil separator.
Anemometer / Flow meter Testo 410-2 0.4 – 20 m/s, -10 ... +50°C Control of the volume flow rate of cooling air in the compressor room.
Laser Tachometer / Stroboscope Testo 465 1 – 99999 rpm Checking of the cooling fan speed and belt drive.

4. Initial Assessment Checklist

Parameter for checking Normal value Trip Value (Warning) Actual value
Working pressure in the system 7.0 – 8.5 bar 10.0 bar (excess pressure) [ ] Record: ______ bar
Oil level in the oil reservoir Center of the viewing glass (hot state) Below the minimum or completely filled glass [ ] Record status: ______
Ambient Temperature +5°C ... +35°C > +40°C or < +2°C [ ] Record: ______ °C
Discharge temperature (at the outlet) 75°C – 92°C 105°C (emergency stop) [ ] Record: ______ °C
Pressure drop on the oil filter < 0.8 bar 1.5 bar [ ] Record: ______ bar
Pressure drop across the oil separator < 0.5 bar > 1.0 bar [ ] Record: ______ bar

5. Systematic Diagnostic Block Diagram

  1. Symptom: High scavenging temperature (> 100°C)
    • Check the level and condition of the oil in the oil tank.
      • IF the level is low → Cause A (Insufficient oil amount / leakage). Top up the oil, check the system for leaks.
      • If level is normal or exceeded → Check the radiator temperature mode using an infrared thermometer.
    • Check the temperature difference at the inlet and outlet of the oil cooler (radiator).
      • IF the temperature difference is less than 10°C (radiator is cold or uniformly warm) → Cause B (Heat exchanger contamination or thermostat failure). Perform the thermostat valve check procedure.
      • If the radiator is hot over the entire area, but the discharge temperature is high → Check the room ventilation and the condition of the radiator fins.
    • Check the air flow and surrounding conditions.
      • IF temperature in the room > 40°C or blocked air filters in the room → Cause B (External temperature factors and insufficient air exchange). Clean the filters, organize forced ventilation according to EN 378.
      • IF ventilation is normal → Check the quality and oil level of the compressor oil.

6. Fault Matrix and Causes

Symptom Likely causes (by likelihood) Diagnostic Test Expected result upon confirmation of the cause
Sudden temperature rise to 105°C within 10-15 minutes after start-up 1. Sticking of the thermostat valve in the closed position
2. Critically low oil level
Measure the temperature of the bypass pipe before and after the thermostat using a pyrometer or thermal imager. The radiator tube remains cold, while the bypass hot side is hot. Oil bypasses the cooler.
Gradual temperature rise over weeks/months 1. External or internal contamination of the oil cooler
2. Degradation (aging) of the lubricant
Evaluate the temperature difference on the cooler and check the kinematic viscosity of the oil. Delta temperature on the radiator < 5°C. Presence of scale (for water-cooled) or dust/oil (for air-cooled).
High temperature is accompanied by frequent activation of protection in summer 1. Insufficient ventilation of compressor
2. Clogged air filters of the chamber
Measure the air flow velocity through the ducts using an anemometer and the temperature in the room. The temperature in the room is 15°C higher than outdoor, the air consumption is below the calculated value.
High temperature rise + increased current consumption by the motor 1. Excessive pressure in the network (> 10 bar)
2. Wear of the screw block bearings
Check the boost pressure manometer and perform a vibration spectral analysis of the block (ISO 10816-3). Vibration on the bearing housing exceeds 4.5 mm/s (zone C/D). Pressure is set above nominal.

7. Root Cause Analysis of Each Fault

A. Failure of the Thermostatic Valve

Why this happens: The thermostatic element (with wax filling) loses its properties due to prolonged operation under high cyclic loads or due to deposits of sludge/lacquer in the oil. As a result, the valve remains stuck in the "radiator bypass" position, directing all the hot oil directly back into the screw block.

Як підтвердити: За допомогою тепловізора зафіксуйте розподіл температур на корпусі термостатичного клапана. Якщо температура лінії рециркуляції висока, а лінія до маслоохолоджувача залишається низькою при досягненні олією температури відкриття (зазвичай 70-75°C), термостат несправний.

Наслідки: Швидке коксування олії, утворення лакових відкладень на зазорах гвинтового ротора, спрацьовування аварійного датчика температури (105°C) та зупинка компресора.

B. Contamination of the oil cooler (radiator)

Чому це відбувається: Всмоктуване повітря містить пил, мастилотуманоподібні домішки або волокна, які осідають на ламелях повітряного радіатора. У водяних охолоджувачах відбувається утворення мінерального накипу (карбонатів кальцію та магнію) на внутрішній поверхні трубок через жорсткість технічної води.

Як підтвердити: Оцініть ефективність теплообміну за формулою дельти температур. Для повітряних радіаторів — візуальний огляд ламелей через сервісні вікна із застосуванням переносного освітлення.

Наслідки: Зниження теплової ефективності призводить до постійного перегріву мастила, зниження його в'язкості, падіння мастильної здатності та прискореного зношування підшипників ковзання/кочення в гвинтовому блоці.

B. Insufficient ventilation and high ambient temperature

Чому це відбувається: Неправильний розрахунок припливно-витяжної вентиляції компресорної станції або відсутність повітроводів гарячого повітря на вулицю. Влітку температура в приміщенні може перевищувати 40°C, що виключає нормальний теплообмін.

How to confirm: Compare the air temperature at the compressor inlet with the ambient temperature. Record the decrease in performance and increase in discharge temperature during the day.

Наслідки: Робота обладнання на межі температурних лімітів, частий аварійний зупин, значне скорочення терміну служби електронних компонентів та контакторів у шкафу керування.

8. Step-by-step troubleshooting procedures

Procedure 1: Replacement or Repair of a Thermostatic Element

  1. Perform the LOTO procedure: disconnect the compressor power supply, release the residual pressure in the oil tank to 0 bar.
  2. Allow the unit to cool down to a safe temperature (< 40°C).
  3. Remove the cover of the thermostat valve by loosening the mounting bolts.
  4. Remove the retaining ring and the old thermostat element together with the sealing rings (O-rings).
  5. Thoroughly clean the internal cavity of the housing from oil residues and deposits using a degreaser.
  6. Install the new original thermostat element (according to the manufacturer's specification) and new sealing rings, lightly lubricating them with clean compressor oil.
  7. Reassemble the unit in the reverse order. Tighten the cover bolts crosswise according to the OEM instruction (usually 25-35 N·m for M8 thread).
  8. Start the compressor in idle mode and check the connections' tightness and the heating of the cooling lines.

Procedure 2: Cleaning the oil cooler (external and internal)

  1. Для повітряних радіаторів:
    • Знеструмте компресор (LOTO). Демонтуйте захисні кожухи для доступу до поверхні радіатора.
    • Видаліть сухий пил та пух за допомогою стисненого повітря низького тиску (до 3 bar), продуваючи в напрямку, зворотному нормальному потоку повітря.
    • При наявності жирових забруднень нанесіть спеціальний промисловий миючий розчин (pH-нейтральний, безпечний для алюмінію). Залиште на 10-15 хвилин.
    • Змийте бруд струменем води під помірним тиском (не вище 5 bar, щоб не погнути тонкі ламелі алюмінієвого радіатора). Уникайте потрапляння води на електричні двигуни та клеми.
  2. Для водяних радіаторів (пластинчастих або кожухотрубних):
    • Від'єднайте водяні магістралі, перекривши запірну арматуру.
    • Підключіть мобільну станцію хімічної промивки (CIP) із розчином інгібітора накипу (слабка кислотна основа на базі сульфамінової або лимонної кислоти).
    • Циркулюйте розчин протягом 2-4 годин за температури 40-50°C.
    • Промийте систему чистою водою до нейтрального показника pH вихідної води.
  3. Post-repair check: Perform a test run. The temperature difference on the cooler should be at least 15-22°C during full load.

9. Preventive Measures

Primary Cause Preventive strategy Monitoring method Recommended interval
Radiator Contamination Regular blowing with compressed air and cleaning of the blades with special tools. Temperature differential control at the inlet/outlet of the oil cooler. Monthly (or every 500 hours)
Thermostat rating Planned replacement of the thermostat element together with the grease. Checking of discharge temperature using SCADA or controller. Annually (or every 4000 hours)
Oil degradation Quality analysis of compressor oil (acid number, viscosity). Laboratory analysis of oil samples (according to ISO 4406). Every 2000 hours or 6 months
Ventilation failure Control of cleanliness of room air filters and operation of exhaust fans. Temperature measurement in the compressor station. Weekly

10. Spare Parts and Components

For restoring the functionality of compressor equipment, use certified spare parts from the European catalog of UNITEC-D GmbH.

Detail Description Specification When to replace Category UNITEC
Thermostatic element Opening range 71°C – 78°C, brass/stainless steel Every 4000 hours of operation or upon failure Thermostat Components
Sealing kit (O-Rings) FKM (Viton), oil resistant, -20°C ... +150°C At each disassembly of the thermostat node or filters Sealing elements
Fine oil filter Filtering accuracy 10-25 microns, operating pressure up to 16 bar Every 2000 hours or when pressure drop > 1.5 bar Filter elements
Synthetic compressor oil ISO VG 46 / VG 68 (polyalphaolefins or diesters) Every 4000-8000 hours (depending on the type of base) Lubricants

Full range of spare parts for industrial compressors is available in our electronic catalog: https://www.unitecd.com/e-catalog/

11. References

  • ISO 10816-3: Vibration control of industrial machines with power over 15 kW.
  • EN 378: Refrigeration systems and heat pumps. Safety and environmental requirements.
  • ISO 4406: Hydraulic fluid. Method of coding the level of solid particle cleanliness.
  • Technical Regulations of Ukraine: Technical Regulation on Machinery Safety (Decision of the Cabinet of Ministers of Ukraine No. 62), CE CERTIFICATION / UkrSEPRO.
  • Related Guides UNITEC: "Diagnosis of Oil Separator Pressure Drop in Screw Compressor", "Technical Maintenance of Lubrication System in Industrial Compressors".

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles