Technical maintenance of conveyor systems in Ukrainian industrial enterprises

Technical analysis: 151685

Technical maintenance of conveyor systems in Ukrainian industrial enterprises

Introduction

Conveyor systems are critical transportation arteries on Ukrainian mining, metallurgical, and processing industry enterprises. Continuous operation of belt conveyors determines the overall productivity of the technological line. Downtime due to failure of drive stations or damage to the belt causes significant financial losses. The average cost of an emergency stop of a heavy conveyor at Ukrainian cement or mining and processing plants ranges from 120 000 to 350 000 UAH per hour, taking into account the loss of production and costs for emergency repairs. Therefore, the implementation of strict maintenance schedules in accordance with the requirements of DSTU EN 620 and ISO 5048 is a critical task for chief engineers and MRO services.

System Architecture

Industrial belt conveyor consists of several interrelated subsystems, each of which requires specific engineering supervision:

  • Приводна група: Електродвигун змінного струму, редуктор (циліндричний або конічно-циліндричний), муфти та приводний барабан. Забезпечує передачу крутного моменту з розрахунковим тяговим зусиллям.
  • Conveyor belt: Multi-layer rubber-coated or rope conveyor belt with working covers of different thicknesses (DIN classes Y, W, X, according to ISO 10214).
  • Натяжний пристрій: Гравітаційний або гвинтовий механізм для підтримання необхідного натягу стрічки та запобігання пробуксовуванню.
  • Roller support: Upper grooved rollers, lower straight or disc rollers rotating on 6200/6300 generation bearings with 2RS or 2Z seals.
  • Pneumatic Control Subsystem: Used for tensioning, belt cleaning and positioning. For example, pneumatic cylinders and distributors, in particular components of the Festo 151685 standard, which ensure accurate positioning of tension elements at an operating pressure of up to 10 bar.

List of critical components

To minimize the time to recovery (MTTR), the following spare parts should always be available in the warehouse of the enterprise:

ComponentTechnical characteristicsFunctional purposeRecommended stock
Drive drumDiameter 630 mm, width 1400 mm, steel S355JRTraction force transfer to the belt1 pc. on 5 conveyors
The roller support is groovedDiameter 159 mm, length 465 mm, bearing 6308-2RSMaintenance of the cargo branch of the tape5% of the total amount
Pneumatic distributor / ValveAnalogue of Festo 151685, working pressure 2.5–10 barControl of tension pneumatic cylinders2 pcs.
Strip ConnectorMechanical lock type (for example, Anker / Flexco)Rubber fabric belt coupling5 sets
Electric motorAsynchronous, 45 kW, 1475 rpm, IP55, IE3Main drive of the conveyor1 reserve for node

Maintenance Schedule

Preventive maintenance system (PMS) is based on operating hours and cycles according to the normative documents:

  • Daily (8 hours): Visual inspection of the belt integrity, checking the tightness of the frame bolted connections, checking for absence of foreign noises in the rollers bearings, checking the oil level in the reducer.
  • Weekly (168 hours): Temperature control of bearing units with pyrometer (limit +75 °C), checking operation of the belt sensor, cleaning drums from material buildup.
  • Щомісяця (720 годин): Вимірювання натягу стрічки, перевірка центрування роликоопор, контроль герметичності пневмоліній (включаючи спрацьовування елементів типу Festo 151685), аналіз вібрації приводного електродвигуна згідно з ISO 10816-3.
  • Annually (8760 hours): Full reducer diagnostics with oil analysis for metal particles, ultrasonic testing of welded joints of metal structures, inspection of braking systems and replacement of worn drum bearings.

Main types of failures

Analysis of operational data of heavy conveyors identifies five most common causes of stoppages:

  1. Roller seizure and sticking (Frequency: 35%, Critical: High): Caused by abrasive dust entering the bearing through the failure of the seal.
  2. Tape shift and lateral slippage (Frequency: 25%, Critical: High): Causes tape edges to be cut by metal structure due to uneven loading or worn out drum linings.
  3. Slip of the drive drum (Frequency: 15%, Critical Average): Occurs due to loss of friction coefficient between the drum and the belt through humidity or wear of the drum's rubber coating.
  4. Failure of the drive reducer bearings (Frequency: 12%, Critical High): Exceeding radial loads or violation of lubrication intervals.
  5. Air leakage in the tensioning system (Frequency: 13%, Criticality: Low): Fitting failure or malfunction of control valves (especially Festo control units), causing the tension force to drop below the calculated 4 bar.
  6. Troubleshooting and Search Guide

    Diagnostic tree for rapid resolution of typical emergency situations:

    • Situation A: The belt is shifting to the left on the idle side.
      Diagnosis: Check the perpendicularity of the lower idler rolls to the conveyor belt axis. If the axis is shifted by more than 1.5 mm, adjust the brackets. Check for material adhesion on the specific idler roll.
    • Situation B: Overheating of the drive drum bearing assembly above +80 °C.
      Diagnosis: Measure the vibration. If there are high-frequency harmonics, immediately stop the conveyor to replace the bearing. If the vibration is normal, add a consistent lubricant (NLGI class 2 on a lithium-complex basis).
    • Situation B: Pressure drop in the belt tension circuit below 3 bar.
      Diagnosis: Check the pressure gauge on the reduction valve. Test the tightness of the pipeline with a soapy solution. If the pneumatic distributor (similar to Festo 151685) does not maintain pressure in the piston area, replace the sealing rings or the valve block itself.

    Spare parts management strategy

    To ensure continuity of production, the critical minimum of spare parts is classified into categories A, B, C according to the ABC analysis method. Category A components (drive drums, electric motors, specialized pneumatic valves) must be kept in a warehouse with zero waiting time for delivery. The delivery time of standard items from European warehouses to enterprises in Ukraine is up to 5-7 working days thanks to well-established logistics. The use of quality certified components reduces the total cost of ownership (TCO) by 22% compared to cheap non-certified counterparts.

    Integration of health monitoring

    Modern industrial safety standards require a transition from reactive to predictive maintenance (Condition-Based Maintenance). The following sensors are installed on the conveyor lines:

    • MEMS vibration sensors: Mounted on the bearing housings of gearboxes and drive drums for continuous measurement of the vibration frequency (mm/s) for ISO 20816.
    • Infrared pyrometers: Carry out continuous control of the thermal state of friction nodes.
    • Revolution sensors (encoders): Fix tape slipping by comparing the speed of rotation of the driven and non-driven drums.

    All collected data is transmitted to the company's SCADA system via industrial protocols (Modbus TCP, Profinet), which allows failure to be predicted 150-200 hours before its occurrence.

    Conclusion

    Effective operation of conveyor transport requires compliance with maintenance regulations, use of high-quality spare parts, and constant monitoring of vibration and tension parameters. The use of proven components guarantees compliance with Ukrainian and European safety standards. See the complete range of certified drive elements, rollers and pneumatic fittings in the UNITEC-D E-Catalog.

    Link

    1. DSTU EN 620:2019 Conveyors of continuous action. Safety and electromagnetic compatibility requirements.
    2. ISO 5048:1989 Continuous mechanical handling equipment — Belt conveyors with carrying rollers — Calculation of operating power and tensile forces.
    3. ISO 10816-3:2009 Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts.
    4. DIN 22101:2011 Continuous conveyors — Belt conveyors for loose bulk materials — Basics for calculation and design.

    Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles