Guide to finding and correcting the high temperature mode of the compressor output with a screw shaft

Technical analysis: Troubleshooting screw compressor high discharge temperature: oil level, cooler fouling, thermostat f

Guide to finding and correcting the high temperature mode of the compressor output with a screw shaft

1. Description of the problem and scope of application

This guide is intended for finding and correcting a high temperature outlet of a screw compressor. High outlet temperatures can occur in many types of industrial equipment, including screw compressors used in the chemical, energy, agrochemical and industrial industries. It is classified as a critical issue because high outlet temperatures can damage equipment, reduce efficiency and endanger personnel.

2. Safety during diagnosis

Use personal protective equipment (PPE): gloves, glasses, cut gloves, tools for working in electrically hazardous conditions.
Ensure power is off and follow lockout/tagout procedure: Before starting work, disconnect power and secure equipment to avoid unexpected shutdowns.
Measure the compressor outlet temperature: high temperature can indicate heat build-up in the system, resulting in a hazard to personnel and equipment.

3. Necessary diagnostic tools

Name of the tool Model/Spec Measuring range The goal
Multimeter Fluke 87V 0-2000 mA, 0-2000 V Measurement of voltage, current, resistance
Thermograph FLIR T660 –20 to 1500 °C Determination of heat losses, uneven heating
Vibration analyzer Keysight 35670A 0-100000 Hz Analysis of vibration characteristics
Thermometer Thermalert T-100 –50 to 2000 °C Measurement of outlet temperature
Manometer Testo 510 0-100 bar Pressure measurement in the system

4. First assessment

Item action
1 Check the compressor outlet temperature.
2 Check the pressure in the system.
3 Record the values ​​of the measured parameters.
4 Check the condition of the cooling system.
5 Record measurement history and recent equipment changes.

5. Systematic diagnostic tree

  1. Symptom: High compressor outlet temperature.
    1. Confirmation: Measure the compressor outlet temperature.
      1. Result: Output temperature exceeds 120 °C.
        1. Diagnosis: Check the oil level.
          1. Result: The oil level is below 50%.
            1. Conclusion: Low oil level.
          2. Result: The oil level is normal.
            1. Diagnosis: Check the condition of the cooling system.
              1. Result: The cooling system is blocked.
                1. Conclusion: Blocked cooling system.
              2. Result: The cooling system is normal.
                1. Diagnosis: Check the thermostat.
                  1. Result: The thermostat does not work.
                    1. Conclusion: The thermostat does not work.
                  2. Result: The thermostat works.
                    1. Diagnosis: Check the environmental conditions.
                      1. Result: The ambient temperature is higher than 35 °C.
                        1. Conclusion: High ambient temperature.
                      2. Result: Ambient temperature is normal.
                        1. Conclusion: The high temperature regime of the compressor outlet due to other reasons.

6. Matrix of occurrence of defects

Symptom High quality reasons (by probability) Diagnostic test Expected result if the cause is confirmed
High compressor outlet temperature
  1. Low oil level (35% chance)
  2. Blocked cooldown (30% chance)
  3. The thermostat does not work (probability 20%)
  4. High ambient temperature (15% chance)
  1. Measure the oil level.
  2. Check the condition of the cooling system.
  3. Measure the temperature of the thermostat.
  4. Measure the ambient temperature.
  1. The oil level is below 50%.
  2. The cooling temperature is higher than 70 °C.
  3. The thermostat does not work.
  4. The ambient temperature is higher than 35 °C.

7. Analysis of the causes of the defect

7.1 Low oil level

Low oil levels can be caused by leaks, insufficient mixing of oil with air, or improper storage. If left uncorrected, this results in overheating of the compressor, loss of efficiency and possible wear of parts.

7.2 Blocked cooling

Blocked cooling can be caused by dirt build-up, leaks, or a fan not working. This causes heat to build up in the system, which can cause an explosion or component wear.

7.3 The thermostat does not work

A thermostat that does not work may be due to wear, lack of power, or lack of communication with the system. This results in a lack of temperature control, which can lead to explosion or component wear.

7.4 High ambient temperature

High ambient temperature can occur due to lack of ventilation, improper location of equipment or exposure to external conditions. This leads to an increase in the temperature of the compressor outlet, which can cause an explosion or wear of components.

8. Step-by-step repair procedure

8.1 Low oil level

  1. Measure the oil level.
  2. If the level is below 50%, add oil to the normal level.
  3. Check for leaks.
  4. Close all leaks.
  5. Check the mixing of oil with air.
  6. If mixing is disturbed, install a new filter.
  7. Measure the compressor outlet temperature.
  8. If the temperature is normal, check the next day.

8.2 Blocked cooling

  1. Measure the cooling temperature.
  2. If the temperature is higher than 70 °C, check the condition of the cooling system.
  3. Check for contamination.
  4. Remove impurities from the system.
  5. Check the fan.
  6. If the fan does not work, install a new one.
  7. Measure the compressor outlet temperature.
  8. If the temperature is normal, check the next day.

8.3 The thermostat does not work

  1. Measure the temperature of the thermostat.
  2. If the thermostat does not work, measure the power.
  3. If the power supply is missing, install a new one.
  4. Check the connection with the system.
  5. If there is no connection, establish a new one.
  6. Measure the compressor outlet temperature.
  7. If the temperature is normal, check the next day.

8.4 High ambient temperature

  1. Measure the ambient temperature.
  2. If the temperature is above 35 °C, check the ventilation.
  3. If there is no ventilation, install a new one.
  4. Check the location of the equipment.
  5. If the location is incorrect, change the location.
  6. Measure the compressor outlet temperature.
  7. If the temperature is normal, check the next day.

9. Preventive measures

The reason for the defect Preventive strategy Monitoring method Recommended interval
Low oil level Periodic mixing of oil with air Oil level measurement Weekly
Blocked cooling Periodic cleaning of the system Cooling temperature measurement Weekly
The thermostat does not work Periodic checking of the thermostat Measuring the temperature of the thermostat Monthly
High ambient temperature Periodic inspection of ventilation Measurement of ambient temperature Monthly

10. Relevant parts and components

Part description Specification When to replace UNITEC-D category
Oil ISO 46, 68, 100 After 500 hours of operation Lubricants and oils
Filter Diameter 50 mm After 1000 hours of operation Filters
Thermostat Temperature range –20 to 150 °C After 1500 hours of operation Thermostats
Cooling system Pressure 0-100 bar After 2000 hours of operation Cooling

Go to the UNITEC-D catalog

11. Links

  • DSTU 2471-99: Work with equipment in an industrial environment
  • EN 12100: Safety of production equipment
  • ISO 50001: Energy efficiency management
  • CE: According to Directive 2006/42/EC
  • UkrSEPRO: Certification of industrial equipment in Ukraine

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles