1. Problem Description and Area of Application
Overheating of the hydraulic system is one of the most common critical failures in industrial equipment of Ukrainian enterprises (metallurgy, machinery manufacturing, forging and casting production). When the operating temperature of the hydraulic oil exceeds the allowable limit of +60...+65 °C (for standard mineral oils of HL/HLP class according to DIN 51524), the viscosity of the fluid drops sharply, leading to internal leaks, loss of volumetric pump efficiency, wear of precision pairs and destruction of seals.
This manual covers stationary and mobile industrial hydraulic systems with working pressures from 50 to 350 bar and flow rates from 20 to 500 l/min. Incident severity classification:
- Critical (Emergency Stop): Oil temperature above +80 °C. Risk of jamming of actuating mechanisms, thermal damage to seals (NBR/FKM) and complete failure of the pump. Immediate stoppage is required according to the LOTO procedure.
- Significant (Warning level): Oil temperature in the range of +70...+80 °C for more than 30 minutes. The system operates with reduced efficiency, slow cylinder movements are observed and periodic activation of safety valves occurs.
- Minor (Early Diagnosis): Temperature remains stable at +65...+70 °C. Noticeable decrease in oil viscosity, increased noise level of the pump under peak loads.
2. Precautionary Measures and Safety
<група-попереджень> WARNING! DANGER OF HIGH PRESSURE AND HIGH TEMPERATURE!
Before performing any diagnostic or maintenance work, carry out the following mandatory actions:
1. Carry out the lockout/tagout procedure (LOTO — Lockout/Tagout) on the main power switch of the pump station.
2. Ensure complete release of residual pressure in the hydraulic circuit by opening the pressure gauges or manual drain lines. Remember: hydraulic fluid under pressure over 50 bar may penetrate the skin and cause severe intoxication or amputation.
3. Use the full PPE set: heat-resistant protective gloves (EN 407), safety goggles with side protection (EN 166), flame-resistant clothing.
4. Avoid contact with hot surfaces of the hydraulic distributor, pipes and tank. Temperature over +65 °C causes immediate skin burns. Allow the system to cool down to a safe temperature (+35 °C) before disassembling components. група-попереджень>
3. Required diagnostic tools
For accurate localization of the causes of overheating and checking compliance with ISO and EN standards, the following measuring instruments are used:
| Tool Name | Specification / Model | Measurement range | Purpose in diagnostics | траса>
|---|---|---|---|
| Thermal Imager | Temperature range -20 °C to +350 °C, resolution from 320x240 pixels | -20 °C ... +350 °C | Non-contact temperature gradient scanning on pumps, valves, heat exchangers and pipelines. |
| Digital pressure gauge / Set of pressure gauges | Accuracy class 0.5, connection G1/4" | 0 - 400 bar | Measurement of working pressure on the discharge line, suction line and in the drain line of pumps. |
| Ultrasonic flow meter / Hydrotester | Portable hydraulic flow and temperature tester | 2 - 600 l/min, up to 420 bar | Determination of the actual volumetric flow rate of the pump and the internal leakage values in hydraulic motors and cylinders. |
| Digital multimeter | True RMS, CAT III 1000V / CAT IV 600V | 0 - 1000 V AC/DC, 0 - 10 A, 0 - 40 MOм | Voltage check of proportional and discrete valve electromagnets, coil resistance. |
| Laser Tachometer / Stroboscope | Optical, non-contact | 10 - 99999 rpm | Control of the actual rotational speed of the electric motor and hydraulic pump under load. |
4. Initial Condition Assessment Checklist
Before disassembly or deep intervention, fill out the following operational parameters card:
| Parameter / Observation | Normative value (Permissible) | Actual value | Status (Normal / Alarm) |
|---|---|---|---|
| Oil temperature in the tank (T_tank) | +45 °C ... +55 °C | [Enter value] | [Select] |
| Ambient Temperature | +15 °C ... +35 °C | [Enter value] | [Select] |
| Working pressure on the delivery line (P_set) | According to the machine specification (e.g. 210 bar) | [Enter value] | [Select] |
| Pressure in the axial piston pump drain line | < 1.5 bar (according to ISO 4413) | [Enter value] | [Select] |
| Pressure drop on the oil filter ($\Delta$P) | < 1.5 bar (new: < 0.5 bar) | [Enter value] | [Select] |
| Level of working fluid in the tank | Min. 80% window level (Optic level gauge) | [Enter value] | [Select] |
| Cleanliness of the working fluid (cleanliness class according to ISO 4406) | No worse than 18/16/13 (or as per OEM requirements) | [Enter value] | [Select] |
5. Systematic Diagnostic Block Diagram
Use this algorithm for step-by-step fault detection:
- Step 1: Locating the heat source using an infrared thermal imager.
- Turn on the system under operating load.
- Scan the hydraulic unit with an infrared thermal imager.
- If a hot spot is detected on the pump: Check the pressure in the drain line. If the drain is hot and the flow exceeds 5-7% of the nominal flow rate — Likely wear or damage to the shaft/piston pairs of the pump (Go to section 7.1).
- If the hot spot is on the fuse or bypass valve: Check the pressure setting and seat condition. The valve continuously drains the flow to the drain line under full pressure — Likely sticking or incorrect fuse valve setting (Go to section 7.2).
- If there is a hot spot on the oil cooler (heat exchanger), but the outlet temperature of water/air is low: Check the cooling medium flow rate and the presence of dirt on the fins — Likely external or internal dirt on the heat exchanger (Go to section 7.3).
- If the hydraulic tank and piping are uniformly hot: Check the overall power balance, pressure drop across the throttles and the operation of the unload circuit during cycle pauses — Likely excessive hydraulic energy losses in the main lines or insufficient tank volume (Go to section 7.4).
6. Matrix "Symptom - Cause - Test - Expected Result"
| Symptom | Likely causes (by likelihood) | Diagnostic Test | Expected result, if the cause is confirmed |
|---|---|---|---|
| High pump drain temperature (> +75 °C), metallic noise. | 1. Wear of the piston pair of the axial piston pump. 2. Cavitation due to air ingestion. |
Measure the flow in the drainage line using a hydrotester. | Drainage consumption exceeds 10% of the pump's rated delivery at nominal speed. |
| Local heating of the safety valve body is above +75 °C. | 1. Continuous flow loss through a faulty or improperly set valve. 2. Contamination of the valve cone with particles. |
Check the temperature difference before and after the valve using an infrared thermometer and measure the pressure at the inlet. | The temperature of the pipe after the valve is significantly higher (> +10 °C), the inlet pressure equals the setpoint. |
| Overheating of the entire system during idling operation. | 1. Contamination of the air-oil radiator. 2. Low cooling water flow rate (for water heat exchangers). 3. Incorrectly selected pump or prolonged operation on bypass. |
Measure the effectiveness of the heat exchanger: temperature difference of the oil and the cooling agent ($\Delta$T). | Heat exchanger efficiency below 50%, heat transfer coefficient has dropped due to scale or dirt layer. |
| Rapid oil heating upon activation of the actuating cylinders. | 1. Internal leakage in hydraulic cylinders through worn piston seals. 2. Excessive pressure setting of pressure reducing valves. |
Perform a leakage test: block the cylinder in the extreme position and measure the pressure drop or heating of the rod cavity. | Rapid increase in the temperature of the hydraulic cylinder wall in the piston area without rod movement. |
7. Root Cause Analysis of Each Fault
7.1. Volumetric wear of an axial piston pump
Чому це відбувається: Аксіально-поршневі насоси високого тиску критично залежні від чистоти робочої рідини (рекомендований клас за ISO 4406 не гірше 18/16/13). Потрапляння абразивних часток призводить до мікроподряпин між розподільною шайбою та блоком циліндрів, а також між плунжерами та гільзами. Це збільшує зазори, через які гаряче масло під високим тиском перетікає в корпус насоса (внутрішні витоки), миттєво нагріваючи його.
Як підтвердити: Підключіть розходомір на дренажну лінію корпусу насоса. За стандартом ISO 4413, якщо дренажна витрата становить більше 8-10% від номінальної продуктивності насоса при номінальних обертах і робочому тиску, насос потребує негайного капітального ремонту або заміни.
Наслідки: Повне заклинювання насоса, руйнування приводу, викид металевої стружки по всьому гідравлічному контуру з виходом з ладу всіх розподільників і клапанів.
7.2. Continuous actuation or sticking of the safety valve
Чому це відбувається: Якщо гідравлічна схема спроектована так, що насос постійно подає повний потік через запобіжний клапан (наприклад, у схемах з нерегульованими шестеренними насосами без розвантажувальних розподільників), вся гідравлічна енергія перетворюється на тепло ($P \ imes Q$). Також клапан може не закриватися повністю через потрапляння сторонніх часток під запірний конус.
Як підтвердити: Виміряйте тиск манометром безпосередньо перед клапаном та порівняйте його з номінальним робочим тиском системи. Використовуйте тепловізор: температура труби зливу від клапана буде вищою за температуру в баку на +15...+25 °C.
Наслідки: Хронічний перегрів масла, деградація присадок у маслі (розрив молекулярних ланцюгів), втрата змащувальних властивостей.
7.3. Heat Exchanger Efficiency Below Calculated
Чому це відбувається: Забруднення ламелей повітряного радіатора пилом, жиром або технологічними відходами підприємства. У водяних теплообмінниках (кожухотрубних або пластинчастих) — утворення накипу, мінеральних відкладень або біологічного слизу на поверхні теплообміну з боку охолоджуючої води.
Як підтвердити: Розрахуйте ефективність теплообмінника за формулою температурного напору. Якщо різниця між температурою масла на виході з охолоджувача та температурою охолоджуючого середовища на вході становить менше 5-8 °C, тепловіддача занижена.
Наслідки: Теплова рівновага системи зміщується в зону небезпечних температур (> +70 °C), що зупиняє виробничу лінію через аварійні датчики температури.
8. Step-by-step troubleshooting procedures
8.1. Pump Unit Restoration Procedure
- Perform the LOTO procedure and release the pressure in the system.
- Remove the worn pump, check the alignment of the pump shaft and electric motor using a coupling (permissible radial runout < 0.05 mm).
- Clean the suction line and replace the filtering elements (pump and filters according to the standards DIN 24550).
- Install a new pump (for example, a variable displacement axial piston pump series A10VSO or an equivalent from the UNITEC-D catalog).
- Before starting, fill the pump housing with clean oil through the drain hole to ensure initial lubrication.
- Perform a cold start in the "recirculation" mode without load for 10 minutes, slowly releasing the remaining air from the control line.
- Check the drain line pressure: it should not exceed 1.2 bar.
8.2. Cleaning and Repair Procedure for Heat Exchangers
- Perform LOTO, isolate the cooling water line and lubrication main by closing the shut-off valves.
- Remove the heat exchanger or connect the chemical cleaning station (CIP).
- For air radiators: perform purge with compressed air under pressure not exceeding 4.0 bar and wash with mild cleaning agents (avoid damage to aluminum fins).
- For plate/pipe-shell water heat exchangers: perform cleaning with a special acidic solution (solution based on sulfamic or citric acid 5-10%) for 2-4 hours to remove scale (according to standards EN 13445).
- Clean with clean water, check the tightness by hydraulic testing with a test pressure of 1.5 times the nominal (but not less than 10 bar) for 15 minutes.
- Install with replacement of sealing rings made of FKM (Viton) to ensure thermal resistance up to +200 °C.
9. Preventive Measures
| Primary Cause | Preventive strategy | Monitoring method | Recommended interval |
|---|---|---|---|
| Pump wear due to contamination | Oil cleanliness class control, implementation of fine filters (β20 $\\ge$ 200). | Oil Sample Analysis in a Certified Laboratory (Particle Counting by ISO 4406). | Every 500 hours of operation (or once every 3 months). |
| Cooling Radiator Contamination | Regular cleaning of blades from industrial dust and grease. | Visual inspection and control of temperature difference ($\Delta$T) on the heat exchanger. | Every 250 hours (or monthly in dusty workshops). |
| Thermal degradation of oil | Control of additive package and viscosity (classification ISO VG 46 / 68). | Measurement of total acid number (TAN) and water content (Karl Fischer). | Every 2000 hours or once a year. |
10. Spare Parts and Components
For rapid restoration of the temperature balance and sealing of your company's hydraulic systems, use proven components from our warehouse in Germany with delivery to Ukraine:
| Description of the part | Specification / Standard | When to replace | Category UNITEC-D |
|---|---|---|---|
| Axial-piston pump with variable displacement | Rexroth A10VSO / Parker PVplus series, 28 - 140 cm³/rev, 280 bar | When the drainage flow exceeds > 10% or the supply is lost. | High Pressure Hydraulic Pumps |
| Air-oil heat exchanger | Cooling capacity 5 - 50 kW, 24VDC / 380VAC motor fan | When the cooling efficiency decreases or mechanical damage occurs to the lamellae. | Cooling systems and heat exchangers |
| Pressure filter element / drain filter element | Woven glass fiber, filtration rating 10 microns (β10 $\\ge$ 75), DIN 24550 | When the contamination indicator (ΔP > 1.5 bar) activates or every 1000 hours. | Hydraulic filters and components |
| Seal kit for hydraulic cylinder / valve | FKM (Viton) / PTFE composite materials, resistance to +200 °C | When external leaks occur or during each major overhaul of the unit. | Seals and Repair Kits |
| Safety valve, direct or reverse acting | Du 10 - Du 25, setting up to 315 bar, ISO 6264 / CETOP | When the cone sticks, loss of sealing or inability to stabilize the pressure. | Hydraulic valves and regulators |
Order the required spare parts directly through our industrial equipment electronic catalog: https://www.unitecd.com/e-catalog/
11. References and Regulatory Basis
- ISO 4413: Hydraulic fluid. General rules and safety requirements for systems and their components.
- ISO 4406: Hydraulic fluids. Method of coding the level of solid particle cleanliness.
- DIN 51524 Part 2 / 3: Lubricants and greases. Hydraulic oils types HLP and HVLP.
- EN 13445: Non-heated pressure vessels (standards for heat exchangers and tanks).
- Technical Guides from OEMs: Bosch Rexroth RE 92701, Parker Hannifin Hydraulic Troubleshooting Guide, Hydac Technical Documentation.
- Related Guides UNITEC-D: "Analysis and Filtration of Working Fluids in Hydraulic Systems of Pressing Equipment", "Prevention of Cavitation Damage in Piston Pumps".
Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt