Sealing Technology for Centrifugal Pumps: Comparison of Single, Double and Cartridge Systems

Technical analysis: Mechanical seal technology for centrifugal pumps: single vs double vs cartridge seals

Sealing Technology for Centrifugal Pumps: Comparison of Single, Double and Cartridge Systems

1. Introduction

Reliability of centrifugal pumps in Ukrainian industrial enterprises directly depends on the condition of the shaft sealing units. Leakage of the working medium through the stuffing box or worn-out mechanical seal accounts for more than 40% of the total number of pump failures on chemical, metallurgical and energy facilities. Choosing the correct seal construction — single, double or cartridge — is a critical decision for minimizing downtime (MTTR) and increasing the mean time between failures (MTBF), which for modern pumps should exceed 25 000 hours.

Operating conditions on Ukrainian enterprises often require equipment to operate in harsh modes: pumping abrasive suspensions in the mining and mineral industry, aggressive acids in the chemical industry, and hot water in thermal energy. UNITEC-D GmbH supplies a full range of certified seals complying with European and Ukrainian safety standards. Understanding the physical principles of operation and selection criteria of seals enables reliability engineers to prevent emergency shutdowns.

2. Fundamental Principles

The face seal operates by creating a flat perpendicular contact between two high-precision rings: a rotating one (on the shaft) and a stationary one (in the stuffing box). Sealing is ensured by hydrostatic and hydrodynamic equilibrium in the microgap between friction pairs, the thickness of which ranges from 0.1 to 1.0 microns.

The key parameter is the hydraulic balance of the seal ($K$). The balance coefficient is determined by the ratio of the pressure area to the friction pair surface area:

K = (A_h - A_f) / A_f

Where $A_h$ is the area on which the medium pressure acts, and $A_f$ is the total contact area of the friction pair. Unbalanced seals ($K > 1$) quickly fail at pressures above 10 bar due to the displacement of the lubricating film between the rings. Balanced seals ($K \approx 0.7 - 0.8$) allow reducing the load on the contact surfaces, ensuring reliable operation at pressures up to 50 bar and above.

Heat generation in the contact zone is a critical factor. Friction creates a significant amount of heat, which must be removed by the flowing liquid or the sealing liquid. When the liquid film in the gap evaporates, dry friction occurs, leading to thermal shock, cracking of silicon carbide or tungsten carbide, and immediate seal failure.

3. Technical specifications and standards

Design, manufacturing and application of face seals are governed by a strict system of international and national standards. Compliance with these standards ensures interchangeability of parts and safety of operation on hazardous production sites in Ukraine.

  • ISO 3069 / DIN 24960: Defines the basic dimensions of mechanical seal chambers for centrifugal pumps, ensuring standardization of space for cartridge seal installation.
  • API 682 (4th edition): The highest industrial standard for seal systems of centrifugal and rotor pumps in the oil and gas and chemical industries. Classifies seal configurations (Categories 1, 2, 3) and flushing systems (API Plans 11, 21, 32, 53A, 54, etc.).
  • DSTU GOST 32622: State Standard of Ukraine for end seals for centrifugal pumps, defining test methods and requirements for materials.
  • EN 12756: European standard for mechanical seals, regulating nominal sizes from 10 mm to 100 mm and nominal pressure.

According to the CE and UkrSEPRO regulations, all components supplied by UNITEC-D GmbH undergo a strict testing cycle, including the check of the roughness of the friction pair surfaces ($Ra \le 0.1\, \mu m$), flatness (within 1-3 sodium light wavelengths) and hydrostatic testing of the housing.

4. Selection and Sizing: Single, Double and Cartridge Systems

The correct choice of sealing architecture is determined by the properties of the fluid (toxicity, abrasiveness, temperature, viscosity), pressure and rotational speed of the shaft ($n$, rpm).

Single face seals

They are used in non-toxic, non-aggressive environments with good lubricating properties (for example, clean water, petroleum products). They come into direct contact with the working fluid. For heat dissipation and to prevent deposits, cleaning according to API standard (Plan 11 or 21) is often used.

Double face seals

They consist of two seal rows (internal and external) with an intermediate chamber for barrier or buffer liquid. They are used for toxic, explosive, volatile or highly abrasive environments. Double seals are divided into "back-to-back" and "face-to-face" configurations. Barrier liquid is under pressure exceeding the pump pressure by 1.5–2.0 bar, guaranteeing complete absence of product leakage into the atmosphere.

Cartridge Seals

They consist of a pre-assembled unit including the shaft sleeve, stuffing box, friction pair and spring assembly. The cartridge construction eliminates the risk of installation errors (incorrect setting of the spring working length), reduces maintenance time by three times and guarantees surface parallelism.

<਼tr style="background-color: #f2f2f2;">
Comparison Criterion Single seal Double seal (tandem/double) Cartridge seal
Typical Environments Water, oils, non-toxic liquids Aggressive acids, toxic gases, abrasive slurries Universal (according to selected friction pair)
Maximum pressure (bar) Up to 25 bar Up to 50+ bar Up to 40 bar
Maximum temperature -40°C ... +220°C (depending on elastomers) -50°C ... +400°C (with cooling) -50°C ... +300°C
Risk of emission into the atmosphere Possible due to wear Practically zero (with a proper barrier system) Depends on the scheme (single or double cartridge)
Mounting time (hours) 1.5 – 3.0 years (requires precise measurements) 3.0 – 5.0 years (complex winding) 0.5 – 1.0 year (previously adjusted)
Відповідність стандартам ISO 3069, EN 12756 API 682, ISO 21049 ISO 3069, API 682

5. Best Practices for Installation and Commissioning

About 50% of premature failures of end seals are caused by violation of the installation technology. Installation engineers must follow the following mandatory procedures:

  1. Shaft geometry check: Radial runout of the shaft in the seal area shall not exceed 0,05 mm. Axial displacement of the shaft is limited to a value of 0,13 mm. Exceeding these limits causes cyclic loading on the spring assembly and destruction of the friction lining.
  2. Cleanliness of the environment and installation: Any mechanical contaminants (scale, sand) that get onto the friction pairs during assembly cause abrasive wear during the first hours of operation.
  3. Use of mounting clamps: When installing cartridge seals, it is strictly prohibited to remove or loosen the factory-fitted lockings (locking plates) until the bolts of the stuffing box and the shaft coupling are fully tightened.
  4. Checking the lubrication system (API Plans): Before starting the pump, ensure that the flushing flow is present, open the cooling valves, and fill the buffer tanks to the operating level. A dry start for even 3–5 seconds will destroy the graphite rings through thermal shock.

6. Failure Modes and Root Cause Analysis (RCA)

Accurate diagnosis of the failure cause allows eliminating the root problem, not just the consequences. Below are the main types of damage and their visual signs:

  • Thermal shock (cracks in rings): Characteristic radial cracks in hard rings (silicon carbide, tungsten carbide). Cause: dry running, absence of cooling or insufficient pressure in the seal chamber.
  • Abrasive wear (grooves and scratches): Deep marks on the friction surfaces parallel to the direction of rotation. Cause: presence of hard particles in the environment, absence of separation or filtration systems (API 31/32 Plan).
  • Chemical degradation of elastomers: Swelling, softening or loss of elasticity of rubber rings (Viton, EPDM, FFKM). Cause: incompatibility of the sealing ring material with the pumped medium or cleaning solutions at elevated temperatures.
  • Corrosive degradation of metallic springs: Appearance of pitting corrosion or complete spring breakage. Cause: aggressive environment in the seal chamber exceeding the resistance of stainless steel (for example, AISI 316 in the presence of chlorides).
  • Free rotation or shearing of pins: Mechanical damage to torque transmission elements. Cause: hydraulic shocks in the system or pump start-up in the reverse direction.
  • 7. Predictive Maintenance and Condition Monitoring

    Transition from preventive maintenance (PPM) to predictive maintenance based on condition (PdM) significantly reduces operational costs. The following methods are used for monitoring end seals:

    • Temperature monitoring of the seal housing: Installing a thermocouple or resistance thermometer directly near the sealing chamber. A rapid temperature rise indicates the breakdown of the lubricating film or failure of cooling.
    • Vibration analysis (spectral analysis): High-frequency vibration (Demodulation / HFE range) indicates the presence of cavitation, imbalance or auto-oscillations in the sealing rings.
    • Coil leakage detection via drain: Use of level sensors or flow meters on the drain lines of non-sealed seals for early detection of degradation of secondary seals.

    8. Conclusions

    Selection and operation of mechanical seals for centrifugal pumps require a systematic engineering approach. Transition to cartridge systems and double seals according to ISO and API 682 standards allows Ukrainian industry enterprises to reduce technological losses, ensure environmental safety and achieve high equipment reliability indicators. UNITEC-D GmbH provides engineering support, pump unit audits and supply of original components and ready-to-use cartridge seals from the European warehouse.

    Familiarize yourself with the industrial components assortment and select the necessary seals for your equipment in our catalog: UNITEC-D E-Catalog.

    9. References

    1. ISO 21049: Pumps — Shaft sealing systems for centrifugal and rotary pumps. International Organization for Standardization.
    2. API Standard 682: Pumps — Shaft Sealing Systems for Centrifugal and Rotary Pumps, 4th Edition. American Petroleum Institute.
    3. DIN EN 12756: Pumps — Mechanical seals — Nominal dimensions and designation. Deutsches Institut für Normung.
    4. DSTU GOST 32622: End seals for centrifugal pumps. General technical specifications.
    5. Mudge, P. "Mechanical Seal Reliability and Troubleshooting Handbook", Industrial Press, 2018.

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles