1. Problem Description and Area of Application
This manual is intended for senior technicians in maintenance, reliability engineers, and workshop supervisors at enterprises in Ukraine. The document covers the diagnosis and troubleshooting of chain conveyors (scraper, plate, bucket), which are used in the grain processing, cement, metallurgical, and chemical industries.
Criticality classification:
- sudden emergency stops due to chain jamming under load, breakage of the drive element, destruction of sprocket teeth or failure of the reducer. Requires immediate intervention and system lockout (LOTO). progressive increase in the current consumed by the drive electric motor by 15-25% above nominal, periodic activation of the thermal protection, increased vibration level (> 4.5 mm/s) and unusual noise or jerky movement of the chain. minor accumulation of material in the underbin area, even chain elongation within tolerance (up to 1.5%), operation without critical temperature deviations of bearing units (< 65 °C).
2. Precautionary Measures and Safety
WARNING! DANGER OF MECHANICAL AND ELECTRICAL INJURY!
Before starting any diagnostic or maintenance work on a chain conveyor, perform the following mandatory actions:
- Full power disconnection (LOTO): Completely turn off the main input switch of the drive motor and switch it to the "Off" position, attaching a lockout device in accordance with occupational safety standards.
- Зняття залишкової енергії: Заблокуйте рух робочого органу механічними стопорами. Переконайтеся у відсутності потенціалу натягу пружин чи натяжних гвинтів. У вертикальних або похилих конвеєрах зафіксуйте гілку ланцюга від самочинного зсування під дією сили тяжіння.
- Засоби індивідуального захисту (ЗІЗ): Використовуйте захисний шолом, захисні окуляри, щільні робочі рукавиці (стійкі до порізів та защемлень), захисне взуття з металевим носком та беруші. Заборонено працювати у вільному одязі біля рухомих частин конвеєра.
3. Required diagnostic tools
| Tool Name | Specification / Model | Measurement range | Purpose |
|---|---|---|---|
| Digital multimeter | True RMS (Fluke 87V or similar) | 0 - 1000 A AC, 0 - 600 V | Measurement of the motor's operating current, checking of winding resistance |
| Laser Tachometer / Stroboscope | Optris / Testo 465 | 1 - 99999 rpm | Definition of the reducer shaft rotation frequency and sprocket |
| Thermal imager | FLIR E8 / Testo 883 | -20 °C ... +550 °C | Temperature monitoring of bearings, gear unit and couplings |
| Portable vibrator | Fluke 810 or SKF Microlog | 10 - 1000 Hz, vibration velocity 0 - 50 mm/s | Balance analysis, gear tooth wear and bearing damage inspection |
| Vernier Caliper / Plug Gauge | Mitutoyo 0-300 mm (DIN 862) | 0 - 300 mm (accuracy 0.02 mm) | Measurement of wear of star wheel teeth and pin teeth of chain |
| Tension gauge / Ruler | Steel measuring rule 1000 mm | 0 - 1000 mm | Chain sag control of the lower or idle branch |
4. Initial Inspection Checklist
| Parameter / Node | Method of inspection | Normative value (Allowance) | Alarm Value |
|---|---|---|---|
| Load current of the motor | Current clamps on phase L1 | <= 85% of nominal on nameplate | 100% nominal for > 5 sec |
| Temperature of bearing units | Thermal imager / contact thermometer | Up to +65 °C (depending on the environment) | +80 °C or difference > 15 °C between adjacent |
| Chain tension (sag) | Visual/Measurement Scale on the Blank Branch | 1.5% - 2.0% of the center distance | Deflection more than 3.5% or full tensioning |
| Oil level and condition in the reducer | Survey glass / sample withdrawal | Center of the window, absence of weights and water | Low level, presence of metal swarf |
| Lubrication system condition | Visual inspection of oil pumps / injectors | Availability of lubricating film on the joints | Dry bearings, signs of corrosion or scoring |
5. Systematic Diagnostic Block Diagram
- Symptom A: The electric drive stops due to an overload emergency signal (the thermal relay or frequency converter issues an overload error by current F001/OC).
- Check the integrity of the mechanical part and the presence of foreign objects in the trough.
- Result C1 (Foreign object / jamming found): Likely cause — entry of metal objects, product degradation or damage to the scraper.
- Perform LOTO locking.
- Open the inspection covers and remove foreign objects.
- Check the scraper geometry.
- Result C2 (No foreign objects, manual rotation difficult): Check the tension and elongation of the chain.
- Measure the chain pitch over 10 links. If the elongation exceeds 2.0% (according to ISO 606), the chain should be replaced.
- Check the condition of the guide rails for wear or scoring.
- Result C1 (Foreign object / jamming found): Likely cause — entry of metal objects, product degradation or damage to the scraper.
- Check the integrity of the mechanical part and the presence of foreign objects in the trough.
- Symptom B: Uniform current increase without complete stoppage, accompanied by surges and increased noise.
- Check the engagement of the chain with the sprocket.
- Result C3 (Chain arcing or jamming on teeth): Likely cause — wear of the driving/driven sprocket teeth or misalignment of the chain pitch to the sprocket pitch due to elongation.
- Measure the tooth thickness of the sprocket and the groove depth using a template or vernier caliper.
- Check the shaft parallelism using the laser alignment tool (ISO 10816).
- Result C4 (Stars and chain in normal condition): Check the lubrication system and presence of material accumulation at the bottom of the conveyor housing.
- Check the effectiveness of the automatic lubrication system or presence of lubrication on the joints.
- Check the lower non-operational branch for product degradation (especially for wet or mineral bulk materials).
- Result C3 (Chain arcing or jamming on teeth): Likely cause — wear of the driving/driven sprocket teeth or misalignment of the chain pitch to the sprocket pitch due to elongation.
- Check the engagement of the chain with the sprocket.
6. Fault Matrix and Causes
| Symptom | Likely causes (by likelihood) | Diagnostic test | Expected result upon confirmation of the cause |
|---|---|---|---|
| Chain slack and noise on the sprocket | 1. Pinion tooth wear 2. Chain elongation 3. Shaft misalignment |
Chain pitch and tooth profile measurement according to a template; checking with a dial indicator | Tooth wear > 15% of initial thickness; chain pitch exceeds nominal by > 1.5% |
| Increase in consumed current (overload) | 1. Material accumulation under the chain 2. Bearing seizure 3. Channel deformation |
Current measurement with clamp meters; bearing temperature check with thermal imager; gap check with feeler gauge | Current > 110% In; bearing temperature > 80 °C; scraper friction against the trough wall |
| Sharp chain break | 1. Pin/plate breakage 2. Impact load (foreign object) 3. Chain stretch |
Visual inspection of the fracture location (brittle fracture or plastic deformation) | Presence of signs of impact scoring or fatigue cracks on the inner plates of the chain |
| Uneven noise and vibration | 1. Dry chain joints 2. Wear of guide plates (polyamide/steel) 3. Drive imbalance |
Vibration velocity measurement using a vibrogram; inspection of friction node condition | Vibration velocity in the vertical direction > 7.1 mm/s (zone C/D according to ISO 10816) |
7. Root Cause Analysis
7.1. Chain Elongation
Why it occurs: Chain elongation is a result of natural and accelerated abrasive wear of the pivot connections (pin bushing roller). The cause of accelerated wear is operation in dusty conditions without proper lubrication, as well as exceeding the design load.
Як підтвердити: Зафіксуйте ділянку ланцюга під натягом 1/10 від розривного зусилля, виміряйте рулеткою довжину 10 або 20 кроків та порівняйте з номінальним значенням за стандартом ISO 606. Збільшення довжини більше ніж на 1.5% вимагає планування заміни ланцюга.
Наслідки: Неправильне зачеплення із зірочкою, вистрибування ланцюга із зубів, пошкодження приводного вала, руйнування скребків та повне заклинювання конвеєра.
7.2. Star Wheel Wear (Sprocket Wear)
Why it occurs: Profile tooth wear occurs due to metal-to-metal friction or abrasive influence of particles of the transported product that enter the engagement zone. Using a new chain with a worn sprocket (or vice versa) leads to catastrophic tooth damage.
Як підтвердити: Виміряйте товщину зуба на висоті кола ділення за допомогою спеціального зубоміра або штангенциркуля. Наявність вираженої "гачкоподібної" деформації (підрізування профілю) свідчить про критичний знос.
Наслідки: Проскакування ланцюга, ударні навантаження на приводний редуктор, зрізання шпонок та вихід з ладу муфт.
7.3. Lubrication Failures (Lubrication Failure)
Why it occurs: Insufficient lubricant, use of incorrect viscosity class, or complete absence of periodic maintenance of chain joints and bearing units.
How to confirm: Check the condition of the joints using a feeler gauge or a white cloth. Dry surfaces, presence of rust or red dust (metal wear products) confirm dry friction.
Наслідки: Скипання мастила в підшипниках, заклинювання рухомих пінів у втулках, різке зростання споживаного струму двигуна через втрати на тертя.
7.4. Material Buildup
Why it occurs: Transporting wet, sticky or caking materials (for example, meal, wet grain, phosphates) on the non-operational branch of the conveyor. The material is drawn under the chain and compressed at the bottom of the trough.
How to confirm: Visual inspection of the lower part of the housing through openings for the presence of tight layers of transported product.
Наслідки: Підняття ланцюга, затискання скребків між ланцюгом та стінками корпуса, критичне перевантаження двигуна та перекіс конвеєрного тракту.
8. Step-by-Step Resolution (Step-by-Step Resolution)
Procedure 8.1. Chain Replacement and Tension Adjustment
- Perform the LOTO procedure for the main motor and close the product delivery shut-off valves.
- Remove the drive guard and tensioning station covers.
- Loosen the counter nuts and loosen the tensioner bolts of the tensioning station to move the tensioning shaft to the extreme front position.
- Remove the worn or damaged chain using detachable links (connecting links).
- Clean the inner surface of the trough from product residues and dirt.
- Install a new chain, following the direction of the scraper movement (the working edge must be oriented according to the manufacturer's technical documentation).
- Connect the ends of the chain with a new connecting element according to DIN/ISO, and secure with cotter pins or retaining plates.
- Adjust the tension: set the tensioning bolts so that the sag of the lower branch is 1.5% - 2.0% of the span length. Tighten the locking nuts with a torque wrench (torque for M20 thread — 350 Nm).
- Perform a trial run on no load for 30 minutes, checking the smooth operation and absence of abnormal noises.
Procedure 8.2. Removal and Replacement of Worn-Out Stars
- Perform full power disconnection (LOTO).
- Remove the chain from the sprocket according to paragraph 8.1 (or leave slack).
- Remove the mounting bolts of the detachable sprocket or remove the locking collars/rings taper-lock on the solid sprocket.
- Using a remover (hydraulic or mechanical) remove the star wheel from the shaft. It is prohibited to use impact tools (hammers) directly on the reducer shaft.
- Clean the shaft seat surface, remove burrs using sandpaper with grit P180, check the shaft runout with a dial indicator (runout tolerance <= 0.05 mm).
- Install a new star wheel, aligning its rotation plane relative to the chain using a laser tool or steel wire (parallelism of axes within 0.1 mm per 100 mm of length).
- Tighten the star-shaped fastening bolts or the clamping sleeve evenly (cross-wise) according to the specified torque (for example, for Taper-lock sleeves 2517 — 48 Nm).
9. Preventive Measures
| Primary Cause | Preventive strategy | Monitoring method | Recommended interval |
|---|---|---|---|
| Chain Lubrication | Timely tension regulation, load control | Chain pitch measurement, tension sensor check | Every 500 hours of operation (or once a month) |
| Star ratings | Application of hardened steels (HRC 45-50), parallel replacement with chain | Visual inspection of gear tooth profile with a template | Every 1000 hours of operation |
| Insufficient lubrication | Installation of automatic lubrication systems or scheduled manual lubrication | Lubrication film check, vibration analysis | Weekly (automatically — daily) |
| Material Accumulation | Installation of lower branch cleaners, control of raw material moisture | Sump and trough filling sensors | Daily visual inspection during shift change |
10. Spare Parts and Components
| Description of the part | Specification | When to replace | Category UNITEC |
|---|---|---|---|
| Drive Chain | Step 100-250 mm, breaking force up to 400 kN (DIN 8165/8167) | Elongation > 1.5%, Pin wear > 10% | Traction chains and components |
| Drive star / tension star | Steel 45 / 40Х, high-frequency quenching of teeth (z=8-16) | Tooth thickness deviation > 15%, formation of nicks | Stars and gears of conveyors |
| Metal scrapers / polyamide scrapers | Thickness 8-12 mm, abrasion resistant (HARDOX / PA6) | Scraper height wear > 20%, cracks | Scraper Blades and Hoist Equipment |
| Bearing units | Series UCP / UCF / SNL (bearing housings) | Increased noise, play, temperature > 80 °C | Industrial bearings |
| Coupling links (locks) | According to the type of traction chain | At each chain replacement or damage | Chain Connecting Elements |
For ordering certified industrial spare parts for chain conveyor systems with delivery throughout all territories of Ukraine, visit our electronic catalog UNITEC-D.
11. Normative References and Documentation
- ISO 606: Roller Chain and Bushing Drive and Conveyor Chains, Sprockets.
- ISO 10816 / ISO 20816: Industrial Equipment Vibration Control.
- DIN 8165 / DIN 8167: Chain Standards for Conveyor Roller Chains.
- DSTU EN ISO 12100: Machine Safety. General Principles of Design. Risk Assessment and Risk Reduction.
- Technical Regulations of Ukraine: Compliance with machine safety requirements (DSTU CE, UkrSEPRO).
- Related Manuals UNITEC: Drive Conveyor Reducer Diagnosis, Technical Maintenance of Heavy Machinery Bearing Units.
Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt