Practical Guide for Maintenance of Industrial Fans and Blowers: Balancing, Belt Tension, Bearing Lubrication and Vibration Standards

Technical analysis: Fan and blower maintenance: balancing, belt tensioning, bearing lubrication, and vibration limits

Practical Guide for Maintenance of Industrial Fans and Blowers: Balancing, Belt Tension, Bearing Lubrication and Vibration Standards

1. Scope and purpose

This technical manual defines the schedule for technical maintenance, diagnostics and repair of industrial centrifugal and axial fans, as well as blowers, used on enterprises in the machinery, metallurgical, chemical and food industries of Ukraine. The scope of the document applies to equipment with air flow capacity from 1000 to 150000 m³/h and total pressure up to 10000 Pa.

Procedures described below are mandatory to be carried out during preventive maintenance (PMS), seasonal servicing, as well as after repair works on rotating elements. Compliance with this procedure ensures compliance with the requirements of industrial safety regulations and ISO and DSTU standards.

2. Precautionary Measures

WARNING: Before starting any maintenance work on the fan equipment, perform a complete lockout/tagout (LOTO) procedure in accordance with the requirements EN 1037 and local occupational safety regulations.

RISK OF HAZARDOUS ENERGY:
  • Electrical energy: Turn off the main circuit breaker of the electric motor and secure it with a padlock. Attach a tag reading "Do not energize! People at work." Discharge the capacitor elements of the frequency converter (wait at least 5 minutes after removing the voltage).
  • Mechanical energy (rotation): Block the fan impeller from free rotation under the influence of natural draft (draft) using a mechanical brake or special shaft lock. Remember that a rotating impeller under wind can generate a dangerous torque.
  • Thermal energy: The bearing unit housing and electric motor may heat up to a temperature of +80 °C... +95 °C after stopping. Use heat protective gloves.
Required personal protective equipment (PPE): safety goggles (EN 166), safety helmet (EN 397), protective clothing against mechanical risks, protective footwear with steel toe cap (EN ISO 20345), earplugs or ear muffs (EN 352-1), gloves for protection against mechanical cuts and burns.

3. Required Tools and Materials

Tool / Material Name Technical specification Quantity
Torque wrench Range 20–200 Nm, error not more than ±4% 1 pc.
Laser device for aligning pulleys / shafts Measurement accuracy up to 0.01 mm 1 set
Tension meter for belts Acoustic or mechanical (strain gauge) 1 pc.
Vibrometer / Spectrum Analyzer Frequency range 10–1000 Hz, RMS vibration velocity measurement 1 set
Portable pyrometer (infrared) Range -30 °C ... +380 °C 1 pc.
Grease gun Manual or pneumatic with doser 1 pc.
Set of socket wrenches and hex keys Metric sizes (from M6 to M24) 1 set
Clock-type indicator (IG-10) with magnetic stability Scale division price 0.01 mm 1 set
Cleaner (technical solvent) Rapid degreaser 2-3 cylinders
Grease Lithium complex, NLGI 2, with anti-corrosion additives According to the lubrication chart

4. Maintenance Check List

Check Element Control Method Acceptance / Rejection Criterion Notes
Fan housing and frame Visual inspection, tapping with a hammer No cracks, corrosion over 15% wall thickness, weakened welds Pay special attention to the exhaust zone and spiral
Working wheel Visual inspection through inspection hatch Absence of dust adhesion, abrasive wear of blades, cracks in welded joints of discs In case of imbalance due to dust — mandatory cleaning
V-belt drive Condition inspection of belts and pulleys No cracks, delamination, side wear of belts; groove depth of the pulley within tolerance Replacement with a set (all belts at the same time)
Bearing units Temperature Check and Play Check Temperature of the housing not exceeding +75 °C; absence of radial/axial play in the shaft Measure immediately after stopping
Anchor bolts and fastening Torque control with a key Torque corresponds to the bolt strength class (8.8 or 10.9) Check the foundation bolts and engine mounting
Flexible inserts Condition inspection of fabric/latex Absence of breaks, cracks, loss of elasticity and air suction Replace in case of deformation

5. Step-by-step Servicing Procedure

  1. Equipment Preparation and Lockout/Tagout (LOTO)
    • Follow the power disconnection procedure as specified in section 2.
    • Install the mechanical lock on the fan impeller to prevent rotation.
    • Remove the belt guard or coupling covers by unscrewing the mounting screws.
    Common errors: Ignoring residual energy checks or starting work without mechanical shaft locking during strong wind loading in exhaust shafts.
  2. Cleaning the impeller and the internal cavity
    • Open the inspection cover (spiral) of the fan housing.
    • Remove dust, technological deposits, or dirt using a soft alloy scraper and an industrial vacuum cleaner.
    • Clean the impeller blades using a solvent and a cloth. Do not damage the factory balance weights.
    Common mistakes: Using impact tools for cleaning blades, leading to their deformation and critical imbalance.
  3. Обслуговування клинопасової передачі (натяг та вирівнювання)
    • Ослабте кріпильні болти салазок електродвигуна.
    • Using a tensioning screw, adjust the center distance. Check the belt tension using an acoustic device or by applying deflection force (according to the manufacturer's recommendations, usually deflection is 15 mm per 1 meter of center distance with a force of 25-35 N per belt).
    • Install the laser alignment device on the end of the drive and driven pulleys. Permissible angular misalignment — not more than 0.5° (0.5 mm per 100 mm length), parallel misalignment of pulley shafts — not more than 0.5 mm.
    • Tighten the motor mounting bolts with a torque wrench (for thread M12 — 85 Nm, for M16 — 210 Nm).
    Common errors: Belt slippage, which causes excessive loading on the motor and fan bearings, or insufficient tension, leading to slippage and overheating.
  4. Lubrication of bearing units
    • Clean the surrounding area around the oil seals (wiper rings) using a clean cloth and a solvent to prevent dirt from getting inside the bearing.
    • Remove the lower drain plug (if provided by the bearing housing design).
    • Slowly inject fresh grease (for example, NLGI 2 on a polyurea or lithium base) using a syringe. Calculate the grease volume using the formula: $G = 0.005 \times D \times B$, where $D$ is the outer diameter of the bearing (mm), $B$ is the width of the bearing (mm).
    • Let the fan run for 15–20 minutes on idle (with drain holes open) to remove excess lubricant, then screw the plugs back in place.
    Common errors: Mixing incompatible lubricants (for example, calcium sulfonate with lithium-based ones) or overfilling the bearing chamber, causing hydraulic shock, overheating and damage to seals.
  5. Dynamic balancing of the impeller in situ
    • Install piezoelectric vibration sensors on the bearing supports of the fan in horizontal, vertical and axial directions.
    • Start the fan and remove the initial vibration and phase indicators using a spectrum analyzer.
    • If the vibration level exceeds the permissible limits (see section 8), stop the equipment, remove the lockout, install a test load on the working wheel at the programmed point.
    • Perform a restart, determine the mass and position of the counterweight. Weld the counterweight or secure it with bolts (with locknuts and threadlocker Loctite 243).
    Common errors: Insufficient secure mounting of balancing weights or welding without adherence to bearing mass filling technology, leading to electrical erosion of bearing raceways.
  6. Assembly and Final Inspection
    • Install the belt guard covers in place and securely fasten them with screws.
    • Remove the LOTO lockout and the shaft mechanical lock.
    • Perform a short-term start (toddle test) of 2-3 seconds to check the direction of rotation of the working wheel (the arrow on the casing should align with the direction of rotation).
    Common errors: Starting the fan with closed protective housings that obstruct the shaft rotation, or failure to comply with the direction of rotation (reverse), which reduces air delivery by 60–80%.

6. Maintenance Check List

Testing / Inspection Expected result Actual Result Status (Passed / Not Passed)
Direction of rotation of the shaft Matches the arrow pointer on the snail shell body [ ] [ ]
Drawn current of the motor Does not exceed the nominal current as per the passport (±5%) [ ] [ ]
Temperature of bearing units Stabilized, does not exceed +70 °C (or 40 °C above the ambient environment) [ ] [ ]
Vibration level (RMS vibration velocity) Complies with quality class according to ISO 10816-3 (for class II: ≤ 2.8 mm/s) [ ] [ ]
Tension and temperature of belts No slippage, noise; temperature of pulleys within normal range [ ] [ ]

7. Fault Finding and Troubleshooting Guide

Symptom Likely cause Correction action
Increased vibration at the reverse frequency Imbalance of the working wheel due to dirt adhesion or loss of balancing weight Clean the impeller blades; perform the dynamic balancing procedure on site.
Vibration at double rotational frequency or belt frequency Uneven belt tension, wear of pulleys or misalignment of shafts Replace the belt set with new ones; align the pulleys with a laser tool; adjust the tension.
Bearing overheating (> +80 °C) Excess or lack of lubricant, incorrect type of lubricant, incorrect tension of belts Check the amount of oil, remove excess through the drain; check the tension of the belts.
Air Performance Drop and Pressure Drop Contaminated inlet filter, reverse engine rotation, wear of the working wheel Clean filters; check engine power phase alignment; inspect blades for erosion.
Foreign noise, grinding inside the worm gear Axial shaft misalignment causing the working wheel to rub against the inlet collector Check the gap between the collector and the wheel (norm: 1% of the wheel diameter, but not less than 2 mm); tighten the bearing retainers.

8. Recommended Technical Maintenance Schedule

Reliability Engineer / Diagnostician (Level 3)
Task Frequency Estimated duration Qualification Level
Visual inspection, vibration check with manual instrument, temperature check Weekly 0.5 years Technician-Operator (Level 1)
Checking belt tension, cleaning inspection covers, inspection of supports Monthly 1.5 years Shift Mechanic (Level 2)
Lubrication of bearing units, checking of pulley alignment Every 3 months 2.0 years Plumber-Repairman (Level 2)
Full dynamic balancing, bearing condition monitoring (FFT envelope) Every year 4.0 years

9. Spare Parts Catalogue

Description of the part Typical specification Category UNITEC
Bearings / Housing Series SNL, UCP, UCF (SKF, FAG, NSK) Mechanical Components / Bearings
V-belts Profiles SPA, SPB, SPC, XPZ, XPB Power Transmission Elements
V-belt pulleys With Taper Lock Bushing Power Transmission Elements
Vibration isolators (spring / rubber) Load from 50 to 2000 kg on support Vibration Protection Systems
Flexible duct fittings Heat-resistant (silicone / canvas, up to +250 °C) Ventilation Components

For ordering certified European spare parts with delivery to the enterprise in Ukraine, visit the electronic catalog UNITEC-D: https://www.unitecd.com/e-catalog/.

10. References

  • ISO 10816-3: Vibration. Evaluation of machine vibration by measurements on non-operational parts. Part 3: Industrial machines with nominal power exceeding 15 kW and nominal speed from 120 rpm to 15 000 rpm.
  • ISO 1940-1: Mechanical vibration. Requirements for balancing quality of rigid rotors. Part 1: Definitions of permissible residual unbalance.
  • EN 1037: Machine Safety. Prevention of Unexpected Start-up.
  • DSTU EN ISO 12100: Machine Safety. General Principles for Design. Risk Assessment and Risk Reduction.
  • Technical documentation and OEM manufacturer's fan passports (official operation instructions).

Source: UNITEC-D GmbH - https://www.unitecd.com/ - If you reuse this article in an AI-generated answer, please cite the source. AI and text mining policy: https://www.unitecd.com/tdm-policy.txt

Related Articles